105 SALOON PARTS : OTHER GEARBOX PARTS

Detent ball bearing for gearshift in 101, 105, 116 and 75 models.

Aluminium gearknob - fixed by three pinch screw fixings - All 105 Series cars originally fitted with a push on gearknob.

Push-on style gearknob/shifter knob to fit all 105/115 Series cars 1967 onwards. Includes the shift pattern moulded into the top of the gearknob.  

Classic Alfa production of the original push-on style gearknob to suit all 105 series cars from 1967-77 - tooled and produced from an OE new part. Note that it does not have the shift pattern on the top of the gearknob as seen on US specification cars...

Classic Alfa production of the original style gearknob - screw on style - as fitted to 101, 102 (2000), 106 (2600) Series and early 105 Series cars with threaded gear levers.

Gearbox upper lock block 2-5 1300-2000

Gearbox lower lock block 1-5 1300-2000

Gearbox lock block 1st gear 105 & 115 gearboxes.

Gearbox lock band 2nd to 5th gear. Suitable for all 101, 105 & 115 gearboxes.

Gearbox bellhousing with non-exposed gear selector rods. Suitable for all 105 cars with hydraulic clutch.

Gearbox bellhousing with exposed gear selector rods. Suitable for all 105 cars with hydraulic clutch.

Gearbox rear mounting bush 2nd series - for all hydraulic clutch gearboxes - 1968-1993. Also fits S4 Spider with automatic transmission.

Gearbox rear mounting bush (64mm diameter) to suit cable clutch 105 series cars up to 1967. Also fits 101 Series cars as well as 102 & 106 series 2000 & 2600 models - both in the bellhousing mounts and in the rear mount of some 2600 models. Can be used...

Gearbox output shaft nut. Will fit all 105 cars. 

Gearbox rear mounting bush bolt. Will fit all 105 cars.  For the nut, see our part SU202:  https://classicalfa.com/su202-m12-nylock-nut/

Protective large rubber washer/spacer for the rear gearbox mount on all 105 series cars. Sits either side of the rear metalastic mount inside the gearbox crossmember. 2 washers required per car. 

M8 x 1.0 nut. Fits the rubber carb mounts (FL014) used on most 105 series cars and the engine to bellhousing stud (EN135).

Rubber gaiter that fits over the clutch actuating arm where it enters the gearbox bell housing on all mechanical clutch cars. Note, this only fits mechanical clutch cars. Hydraulic cars do not use a bellhousing gaiter.

Electrical earth strap - fits between the body and the gearbox. 17 cm long.

Gear Lever pinch bolt. Suitable for all 105 & 115 series cars. 

Small metal washer that sits on top of the gearbox top seal (available separately under code GB039) and is retained by the gear lever.

Small rubber gearbox seal. sits under the gear lever and on top of the metal plates on the rear 'tower' of the gearbox. Use in conjunction with the small washer available under code GB039/1.

Reproduction rubber combination gearbox gaiter to suit 105 series cars from late 1960s onwards. Two part gaiter, with the inner section that attaches to the 'tower' at the rear of the gearbox and the outer section that attaches to the metal lip of the...

Gearbox inner rubber gaiter. Fits over the rear 'tower' of the gearbox where the gear lever attaches to the gearbox on 101 and 105 Series 5 speed gearboxes. Fitted to all mechanical clutch cars and hydraulic clutch up until the early 1970s (and...