Categories

Conrod nut.  Two required per conrod, 8 in total per engine. 1600-2000 engines only, including TS.  We recommend you replace any tab washer once it has been used more than once.  

Exhaust valve guide to suit all 4 cylinder 101, 105, 116 and 75 engines, plus Montreal - with 9mm valve stems. Not TS. Sold individually.

Inlet valve guide to fit all 4 cylinder 101, 105, 116 and 75 engines - plus Montreal - with 9mm valve stems. Not TS. Sold individually. Note, these can also be used as an exhaust valve guide if you wish to fit valve stem seals on the exhaust valves...

Boot floor for all 105 series Berlinas. Does not include the spare wheel well - available under code ST054. NEW PRODUCTION. ** We strongly recommend trial fitting the fuel tank when fitting this part as new and reproduction fuel tanks...

Bonnet/hood & boot/trunk stay spring for stepfront cars.

Bonnet/hood & boot/trunk stay & spring for stepfront cars. If you require the end rubber buffer, please see 750-234 BOOT/TRUNK & BONNET/HOOD STAY ROD BUFFER

Metal strap for the air filter housing on early 105 series cars with the air filter on the exhaust side. 

Air filter to fit the single carb FISPA cannister setup mainly found on early 105 Series Giulia Saloons. Dimensions: Height - 11cm Outer Diameter - 13cm Internal Diameter - 9cm

Giulia rear wing to boot floor panel, left hand side.

Giulia rear wing to boot floor panel, right hand side.

Boot floor for all Giulia Super & Nuova saloon 1300 & 1600 from 1962-77. Does not include the spare wheel well - available under code ST054. NEW PRODUCTION.  ** We strongly recommend trial fitting the fuel tank when fitting this part as new and...

Radiator fan retaining washer, suitable for fitting WA039 WA040 Thickness – 2mm Inner diameter – 36mm Outer diameter – 67.3mm Mounting hole diameter – 7mm PCD – 51mm

Screw for rubber heel mats. Fitted to cars with short carpets including Sprint GT, Sprint GTV, GTC, GTA and 1750GTV Mk1. Two screws are required per mat.

Caliper seal kit to fit Brembo caliper as fitted to Alfa 75 GTV6 (common upgrade to 105 series Alfa) - one kit does one caliper.

Pair of rear rubber heel mats to suit early step front cars. 1965-67 Sprint GT & Giulia GTC. For both left hand drive & right hand drive cars. For the carpets fitted in conjunction with these rubber mats, please see: IN056/1 for RHD cars...

Pair of front rubber heel mats to suit 1965-67 Sprint GT, GTA (1600) & Giulia GTC. For both left or right hand cars. For the carpets fitted in conjunction with these rubber mats, please see: IN056/1 for RHD cars. IN240 for LHD cars...

Rear silencer support bracket. Attaches at one end of the boot floor support panel ST054/2. To suit all 105 Series cars.

Boot floor support panel, attaches onto the side of the spare wheel well. To suit all 105 Series cars. 

Bonnet stay Spiders from 1967 to 1993.

Bumper mounting bracket to suit all European spec (chrome bumper) Series 2 Spiders 1970-82. Please note, originally two of these support brackets were used on each front bumper. Price is for each bracket. Used in conjuction with CH044 & CH045

Spare wheel well fixing bracket, to suit all 105 Series cars.

Front wheel stud - left hand thread - to fit 750,101 and 105 series cars. Length = 52mm (excluding head)

Internal O ring to fit all ATE brake calipers on 105 models and some 116 models. Two required per caliper. Not included in the caliper seal kits available under codes BR035 (front), BR036 (rear) and D0170, must be ordered separately. 10mm outer diameter,...

Bonnet/hood stay arm holder, will fit most late 105 type model cars.