Categories

Bumper mounting bracket for all European spec, (chrome bumper) Series 2 Spiders 1970-82. Two required per car.

Pair of front rubber heel mats to suit Sprint GT Veloce, Mk1 1750 GTV and GTA 1300. For both left or right hand cars. For the carpets fitted in conjunction with these rubber mats, please see: IN056/1 for RHD cars. IN240 for LHD cars...

Fits all Spiders from 1970-1993. Does not include spare wheel well. ** We strongly recommend trial fitting the fuel tank when fitting this part as new and reproduction fuel tanks vary dimensionally and the tank aperture may require adjustment accordingly...

Fits all roundtail cars. Does not include spare wheel well. ** We strongly recommend trial fitting the fuel tank when fitting this part as new and reproduction fuel tanks vary dimensionally and the tank aperture may require adjustment accordingly **

Spare wheel well to suit all 105 Series cars. We have stocks of a new production of this panel that is much improved over the previous version which now includes nicely stamped floor bung holes and small drain hole (all exactly as original). Can be...

Boot floor for all GTs from 1964-77. Does not include the spare wheel well - available under code ST054. NEW PRODUCTION, PERFECT FIT! ** We strongly recommend trial fitting the fuel tank when fitting this part as new and reproduction fuel tanks vary...

Set of pedal aperture finishing rubbers for carpet set. If you are having a carpet set made for your standing pedals Bertone GT these are essential to get the original look & prevent wear & tear to the carpet - set 4 covering the brake and clutch pedals,...

Caliper seal kit to fit all ATE rear brake calipers - one kit does two calipers. Note, if you are splitting the caliper apart, this kit does not include the small internal 'O' rings in the calipers. These are sold separately under item code BR086. 2...

Caliper seal kit to fit all ATE front brake calipers - one kit does two calipers. Note, if you are splitting the caliper apart, this kit does not include the small internal 'O' rings in the calipers. These are sold separately under item code BR086. 2...

Rear wheel stud, right hand thread, suitable for all ATE braked 105 series cars. Length = 52mm (excluding head).

Front wheel stud - right hand thread - to fit 750, 101 and 105 Series cars. Length = 55mm (excluding head)

Bosch type condenser suitable for all 105 series models (and some early Alfettas) 1969-74 with round section insulator & spade electrical connector.

Air filter to fit the single carb FRAM cannister setup mainly found on early 105 Series Giulia Saloons. Dimensions: Height - 13.5cm Outer Diameter - 16cm / 18.5cm Inner Diameter - 11cm

Sport Air filter for better less restrictive induction. To fit the cannister on the early 'crossover' intake as seen on cars up to 1970 (105.26 early type). New production to our own specification, fits much more tightly into both styles of...

Sport Air filter for better less restrictive induction. For cars with cylindrical Air filter - later type (105.48) - to suit later 105s with the filter on the carb side plus some 116 models. Please check measurements before...

750/101 window winder handle with metal grab handle. Round with pin fixing 

750/101 window winder handle with metal grab handle. Square fixing 

750/101 window winder knob

Beautifully made inner door trim panel to suit the 1750 GTV Mk 2. Done in the correct style and skai black material and includes the heat pressed trim lines and chromed strip as well.  Highly recommended and used on our own cars! Please note - all door...

750/101 window winder handle with square fixing

Rubber seal for the reverse light lens. 

Rubber backing for LT022 reverse light. Also fits various model Ferraris as well!

Complete reverse light for roundtail spider 1966-70. Fits under the right side rear bumper.

Iniezione badge to suit US market SPICA fuel injected 105 Series cars. Overall length 15 cm/5.8 inches with 3 mounting pins.