Categories

Rearview mirror support bracket for Spiders 1966-1993 . Before ordering, please make sure this is the correct part for your vehicle. If you require the miroor please click on the following link IN119 SPIDER INTERIOR REAR VIEW MIRROR 1983 ON

Rearview mirror support bracket for some GT models and Giulia . Before ordering, please make sure this is the correct part for your vehicle.

Black rearview mirror support arm for some GT models and Berlina . Before ordering, please make sure this is the correct mirror arm for your vehicle. 

Main bearing locking nut. Suitable for all 4 cylinder engines. 

Pair of front quarterlight pivots set for all GTs and GTVs (inc. GTC / GTA).  

Pair of front quarterlight window pivots for all GTs and GTVs (inc. GTC / GTA). Includes four M3 button head screws to attach them to the quarterlight frame (in place of the original rivets). Please note that 1964-66 cars (with a chromed quarterlight...

Pair of rear inner side window stainless steel covers for all GTs and GTVs from early Sprint GTs onwards. 

Original ATE rear axle brake pressure regulator valve. Normally fitted to cars from 1976 to 1984, however it can be fitted on early cars.  Please note, on some models it may require modification to make it fit.

Rearview mirror support arm for Sprint GT / GTC / GTA and GT Sprint Veloce from 1964 to 1968. This will also fit mk1 1750 GTV, even though originally they were painted black. 

Rear axle brake pressure regulator valve to fit all 105 Series cars. Produced as per original specification with brake switch connection .

Polished rear quarter window outer 'button' to suit all GTs/GTVs. Use in conjunction with the rear quarter window catches available separately under item code CH066 and the rubber seals under item code RB097. Two required per car - one each side.

Pair of rear side window catches for all GTs and GTVs from early Sprint GTs onwards. Note that this does not include the outer domed piece or the retaining 'E' clip, just the inner catch mechanism. The outer chrome 'button' and E clip is...

Pair GT bootlid hinge buffers that prevent the bootlid/trunk lid opening too far on your GT/GTV and damaging the bodywork. Note that some early Stepfront cars have four buffers fitted, while later cars use two located inside the 'loop' of the hinge. Also...

Rear axle brake pressure regulator valve to fit all 105 Series cars. This is similar in design to the unit fitted originally to 1990-93 Spiders but will work on all 105/115 models. Also fits 116 models until 1984. Please note, on some models it may...

GTA 55mm bore centre exhaust section to suit all GTs/GTVs. Made in Italy by IMASAF - OE Quality steel exhaust systems since 1954! This system will require two of the larger gaskets and one larger...

Differential pinion outer (front) bearing to suit the larger pinion fitted to limited slip differentials found in 2000cc cars. Internal diameter 33.3mm, OD 68.26mm, width 22.2mm. 

Pertronix electronic ignition kit - for later cars to replace 1 piece Bosch points, delivers twice the power to the spark plugs, reliable starting every time! Uses Hall effect magnetic sensor in place of the points and unlike optical systems it isn't...

Rev/tacho cable for left hand drive 105 series cars. 1.55m long, it will also suit some 750 & 101 series cars as well. For LHD speedo cable, see part number EN087.

Speedometer cable for all right hand drive 105 series cars. 2.0m long, it will also fit 750 & 101 series cars in need. For a suitable cable for left hand drive cars, see EN087.

1.85M long. Used as the speedometer cable for LHD cars and as the rev/tacho cable for RHD cars. Fits all 750, 101, 105 series cars. Check the length of your old cable! See part EN103 for the rev/tacho cable for LHD cars and EN088 for the speedo cable...

A set of assorted engine tab washers for camshafts, crank pulley, main bearing caps and 5th main bearing cap (later 2 piece style). Fits 4 cyl 101, 105, 116 engines. Some of the washers are used in the Montreal V8. We recommend you replace any tab washer...

Ignition lead clamp to suit 750/101 series Sprints and Spiders. This clamp replaces the original style clamp that was part of the jubilee clip onto the inlet manifold.

Aluminium blanking plate for the rev counter drive. will fit 101 1600 cars plus 105 and 116 series cars with cable driven rev counters. 

3 way brake union to fit on the rear axle of all 105 Series cars including Montreals. Alsp fits some 750 and 101 Series cars. This hoses are compatible with 3/8 UNF unions under the code BR323