Categories

Inner headlamp (5 3/4") mounting frame for 4 headlight Bertone GT / GTV Also fits the right inner headlamp on a Giulia Saloon. 

Complete right side 'B' post/pillar to fit all Spiders 1966-93.

Complete left side 'B' post/pillar to fit all 105 Series Spiders 1966-93.

A pair of rubber seals (left and right) to fit between the tail light unit and the bodywork on all Montreals.

Classic Alfa 5 x 15" Giulietta / Campagnolo style alloy wheel for competition use. Fantastic lightweight alloy replica of an original Alfa/Campagnolo wheel copied in every detail including the original strengthening ribs on the rear and vent hole profile...

Set of 4 outer headlight seals (thin section - fits between outer rim and lens) to fit 2000 & 2600 Touring bodied Spider and 2000/2600 Sprint.  

Spring clip to retain the stainless steel headlight surround on all non-Stepfront GTVs/GT Juniors and Giulia and Berlina saloons 1968 onwards, also fitted on some 750/101/106 series cars.

Nylon 'pull tag' to fit the spring loaded headlight retaining clips on non-Stepfront GTVs & GT Juniors and Giulia and Berlina saloons from approximately 1968 onwards. Fitment advice - soak first in hot water to soften them as they are a very tight fit!

Koni adjustable front shock absorber to fit 1900 series, 102 Series 2000 and 106 Series 2600 cars. Two required per car, we strongly recommend replacing shock absorbers as a pair.

Rubber seat edging trim to fit 750 Series Spider seats. One roll does both seats.

Rubber seat edging trim to fit 750 Series Spider seats. One roll does both seats.

Rubber seat edging trim (red) to fit 101 Series Spider seats. One roll covers both seats.

Rubber seat edging trim (black) to fit 101 Series Spider seats. One roll fits both seats.

Standard con rod/big end bearings to suit 1600, 1750 and 2000 101, 105, 116 and 75 engines, including TS. Produced by an original equipment manufacturer such as Mahle, Glyco or AE depending on availability, and therefore favoured by performance engine...

Pair of rubber seals to fit 7 inch diameter headlights as fitted to later 750 Series and all 101 Series Sprints. Fits between the headlight bowl and the bodywork.

Polished stainless steel ring to suit the lower/high beam headlight (small) on 2600 Spiders.

Pair of rubber seals to suit 5 inch diameter headlights - fits between the headlight bowl and the body of the car.

Complete centre and rear exhaust section to suit all 750 & 101 Series Spiders. Made in Italy by IMASAF - OE Quality steel exhaust systems since 1954! Use clamp EX027

Lower door frame repair section to suit the right side door (looking from the rear of the car) on 101 Series Spiders. Will also fit 750 Series Spider doors with some modification.

Lower door frame repair section to suit the left side door on 101 Series Spiders. Will also fit 750 Series Spider doors with some modification.

Front exhaust section and silencer to suit 1600 Veloce Spiders and Sprint Speciales. Made in Italy by IMASAF - OE Quality steel exhaust systems since 1954! Use gasket 750-079 and clamp EX027

Rubber seal to fit the rear window glass to the supporting frame. Two different types were fitted on Montreals throughout production. Please check your car carefully before ordering. Alternative style please see MN021/2 See item...

New 2000cc cylinder liner that has been precision bored in a special jig to increase capacity to 84.5mm to suit our special high compression Cosworth race pistons - available separately under item code EN513. This bore gives you the maximum available...

New 1600cc cylinder liner that has been precision bored in a special jig to increase capacity to 78.75mm to suit our high-compression Cosworth race pistons - available separately under item code EN511. This bore gives you the maximum available...