Categories

Wosp Performance, high torque starter motor to suit all cars with an 8 tooth pinon starter and 3 bolt mounting. This will fit all 1300/1600/1750 engines from 1968-74 and can also be used on early cars from 1960-67 with a two bolt mounting. ** NOTE ** -...

Spider door glass in the original green tint as used on Series 4 Spiders. This glass can be used on spiders from 1970-93 however earlier cars would have had a bronze tint (S3 Spiders) or clear glass (S2 Spiders). If you require the clear glass, as used...

Bumper, overrider spacer block to suit all GTs with overriders from 1970 onwards. This block is suitable for the front left or the rear right overrider. If you require the front right and rear left please see CH134

Bumper, overrider spacer block to suit all GTs with overriders from 1970 onwards. This block is suitable for the front right or the rear left overrider. If you require the front left and rear right please see CH133

Bosch starter motor, 3 bolt mounting and 8 tooth pinion to suit 1300/1600/1750 engines. ** NOTE ** - If your vehicles is a 1600 from 74 onwards, it may have a 9 tooth starter motor. Please count the teeth on your old starter carefully before...

New headrest for cars made 1970 to 1987. Please see measurements below. Headrest foam dimensions: Width - 20.5cm Height - 11cm Depth - 13cm

105/115 series engine compartment strengthening panels. These panels fit in the area behind where the steering box and idler mount on the outside of the inner wing. Providing extra support and strengthening whilst also cutting down on unwanted body flex...

Plastic wiper shaft spacer to suit 105 series 2 Spiders from 1970-83.

Used Alfetta 2000cc crankshaft. Currently around 020 undersize. Could also be fitted to a 105 series car if the crank were drilled to accept a spigot bush.

Coolant tube fitted on the side of the block, to suit 750 & 101 cars.

Metal retaining clip plate for soft-top cover clip - attaches soft-top plastic clip to hood cover. Spiders 1970-89 - 12 clips required per car. Spiders 1990-93 - 4 clips required per car. Corresponding metal clip & plastic...

GT/GTV door check strap pin to suit all GTVs 2000 & late JUNIORS from 1972 onwards, as well as all Giulia saloon's. This pin goes through the hole in the check strap arm to locate it into the door hinge. Please see: MI018 (Late GTV check...

Courtesy boot light unit for all Montreals.

Used crankshaft from a 1300cc 105 series engine. Big end and main bearing journals are currently at 010 so it has plenty of scope for a re-grind, presumably to 020. Note, the journals have a coating of rust from storage.

Used crankshaft from a 2000cc 105 series engine. Big end journals are currently at 010 and main bearing journals are at 020. Note, the bearing journals have a coating of rust, as can be seen from the photos so a regrind to 020/030 would probably be...

Used crankshaft from a 2000cc Alfetta engine. Main bearing and big end bearing journals are both currently at 010 undersize. As well as 2 litre Alfettas, it will also fit 2 litre 105-series engines if the rear of the crank is drilled out to accept a...

Used crankshaft from a 2000cc Alfetta engine. Main bearing and big end bearing journals are still within STD measurements so it has never been re-ground. As well as 2 litre Alfettas, it will also fit 2 litre 105-series engines if the rear of the...

Spark plug - BCP6ET suitable for the 8V Twin Spark engine. Three electrode and removable top tip.

Fuel filter for all 75 1.8 Turbo models. Also fits Alfa Romeo 916 all models.

Fuel filter for all 75 2.0 Twin Spark models. 

Giulia 105 two piece "GIULIA 1300 TI" script badge. Normally fitted on boot/trunk lid on early Giulia saloon.  SIZE: GIULIA 1300 = 160mm wide,  20mm tall           TI= 25mm wide, 20mm tall

Useful in-line universal fuel filter that can serve as additional fuel filtration or as a cheap replacement for the original filter unit. Suitable for all carburettor-equipped models.

Giulia 105 one piece "Giulia 1300" script badge. Normally fitted on boot/trunk lid on early Giulia saloon.  SIZE: 150mm wide,  25mm tall   

Giulia TI 105 script badge. Normally fitted on boot/trunk lid on early Giulia saloon.  SIZE: GIULIA SCRIPT 100mm wide,  20mm tall.