NEW PRODUCTS

Pair of alloy upper A-post covers to suit a 2600 spider. These covers sit on the underside of the upper portion of the A-panel inside the door shut. Please see photo 4 for a better idea of its location.

Light green tinted front windscreen to suit all later Alfetta GTVs with a bonded windscreen.

Complete early interior rear vision mirror with chrome surround - dipping style - to fit all 105 Series Coupes & Saloons up to 1968. Excellent quality. Also fitted to early 1750 berlina.

Hardtop rear screen seal to suit all Giulietta Spiders with a glass rear screen. If you require the seal for a plexiglass screen please see 750-421

Hardtop rear screen seal to suit all Giulietta Spiders with a plexiglass rear screen. If you require the seal for a glass screen please see 750-422

Boot striker spacer plate (1mm thickness) to suit all 105 GTs. This plate sits under the boot striker to marginally lower it if your boot lid isn't catching properly.

1966-70 Spider Roundtail rear reflector. only.

Rear/tail light lens to suit 750 Series cars. Sold individually. Please study lens picture carefully before ordering, to make sure it matches your vehicle.

Rear soft top drape/cover for 101 series Giulietta Spider.

Soft top channel drain hose to suit 105 Spiders from 1970-93. This is the hose that runs down the B-post to the sill for drainage of the soft top channel. *Please note this hose will do both sides. It just needs to be cut in half and then trimmed to...

Glyco little end/conrod to gudgeon pin bearing to fit 101,105,116 and 75 engines, 1600,1750,2000 and V6 Busso engines. Also fits Montreal engines. Steel back sintered bronze-no overlay, Bi-/Trimetallic.

Headlamp bowl for late cars with ELMA headlight. Please check pictures carefully before purchasing to make sure this headlight bowl is correct for your headlight.

Exhaust tailpipe o-ring for the joint between the centre and rear sections of the exhaust on cars which require a 68mm O ring.

Spider boot hinge bolt 1966-1993. Please note ealry cars were fitted with a step rivet, which will need to be drilled out and can be replaced by this bolt.

Cylinder head nut for all 106 2600 cars.

105/115 series engine compartment strengthening panels. These panels fit in the area behind where the steering box and idler mount on the outside of the inner wing. Providing extra support and strengthening whilst also cutting down on unwanted body flex...

Bush engine block. Locates the lower pulley in the block. MUST BE HONED 2000 engines. Height - 14.5mm

Replica Vega style 6 x 14 inch 4 stud wheels to suit 4 cylinder Alfettas (not the GTV6), new reproduction of classic Seventies alloy wheel, finished in black with polished rim and highlights. 98 PCD Offset ET23 TUV approved.

New alloy reproduction of the Campagnolo Millerighe wheel. 6 x 14 inch, 4 stud with 108 PCD. Offset fitted to later (1968 on) GT/GTV or Spider models. - ET23.

Wiring loom to suit all left hand drive Junior Zagatos. PVC cables with correct style connectors and PVC outer sleeves/tape for protection.

Fuel sender to suit Alfetta GTV6s. For Alfetta Saloons and 4 cylinder Alfetta GTVs please see D0454

Screw for the front quarterlight hinge on all GT cars. This is the screw that goes through the glass from the inside of the car to mount the lower half of the quarterlight hinge.

Specialized socket to suit the Montreal crankshaft nut.

Gear to link the electric window motor to the window regulator. Suitable for use on late Series 3 and Series 4 cars as well as Montreals and Alfetta GTVs. Please see GL015 for the corresponding window motor.