NEW PRODUCTS

Spider S4 & late S3 fuel injectors retaining bolt kit

Spider S4 & late S3 fuel feed line to electric fuel pump, which then connects to part FL133 . Item 2 on the diagram picture. E10 Compatible. Included in the kit jubilee clips and a plastic shroud to protect the section of the hose that goes...

Spider S4 & late S3 fuel tank feed hose to electric fuel pump hose. Item 9 on the diagram picture. E10 Compatible.

Spider black door buffer receiver gaskets. For all Spiders, sold as a pair.

Spider door buffer receiver gasket. For all Spiders, sold as a pair.

Spider door buffer receiver chromed. For all Spiders, sold as a pair.

Spider inner rear valance 1970-82

Rear number plate light seal. fitted on GTs & Saloons and Series 2 Spiders from about 1970 onwards.  

Soft top channel drain hose to suit 105 Spiders from 1970-93. This is the hose that runs down the B-post to the sill for drainage of the soft top channel. *Please note this hose will do both sides. It just needs to be cut in half and then trimmed to...

13mm nut to suit the 8mm propshaft bolt, available under code GB096. 8 required in total per car - 4 each end of the propshaft.

Propshaft bolt - 13mm head and 8mm shank. Note that these bolts (8 required per car) are only suitable for early model cars with 8mm holes in the propshaft ends. See part number GB097 for a matching nut for this bolt.

Carpet set to suit all left hand drive Bertone 1750 GTV mk1 from 1967-69. Produced in the correct orginal style and grey colour . See also item code IN311 for right hand drive Mk 1 1750 GTVs with standing pedals and centre consoles. If you require the...

Carpet set to suit all right hand drive Bertone 1750 GTV mk1 from 1967-69. Produced in the correct orginal style and grey colour . See also item code IN312 for left hand drive Mk 1 1750 GTVs with standing pedals and centre consoles. If you require the...

Wiper mechanism spacer - Fits under the scuttle panel. Please check photos to make sure this is the correct item for your car, as some only used a cylindrical spacer.

Beautifully made red carpet set, made in the correct style to fit all left hand drive Sprint GT, Sprint GTV, GTA Stradale and 1750 GTV Mk 1 cars. To be fitted in conjunction with the rubber heel mats available under part IN056/2.    

Beautifully made red carpet set, made in the correct style to fit all right hand drive Sprint GT, Sprint GTV, GTA Stradale and 1750 GTV Mk 1 cars. To be fitted in conjunction with the rubber heel mats available under part IN056/2.    

Tab washer for the nut that holds on the front crankshaft pulley for all 4Cyl Spica equipped models. We recommend you replace any tab washer once it has been used more than once. Alfa Romeo OE part number 105.50.02.104.00

Beautifully made grey pair of inner door panels to suit all Sprint GTs and GTVs as well as GT Juniors and 1750 GTV Mk 1 models. Done in the correct style and material.     

Beautifully made ochre pair of inner door panels to suit all Sprint GTs and GTVs as well as GT Juniors and 1750 GTV Mk 1 models. Done in the correct style and material.  Rear panels available under IN150/1 SPRINT GT/GTV/GT JUNIOR/1750 MK 1 INNER REAR...

Bonnet/hood & boot/trunk stay spring for stepfront cars.

Bonnet/hood & boot/trunk stay & spring for stepfront cars. If you require the end rubber buffer, please see 750-234 BOOT/TRUNK & BONNET/HOOD STAY ROD BUFFER

Metal strap for the air filter housing on early 105 series cars with the air filter on the exhaust side. 

Cam/Valve cover nut to suit early 750 Veloce Series & Sprint Speciale engines.    6 required per car.

Clutch release bearing to suit 1900/102 series cars. This is the bearing only (not the carrier). Please check the dimensions of your current bearing against the dimensions below as there were some variations on release bearings used over the years...