Categories

'Giulia Sprint GT' boot lid script with three threaded mounting pins. Used on Sprint GTs and also on Sprint GTVs in combination with the 'Veloce' badge available under code BG015.  

Cable style window regulator to suit all Spiders 1970-74 (right side window) with non-electric windows. Note that this regulator has a splined shaft length of approximately 30mm. Later regulators have a shaft length of approximately 40mm. Check yours...

Cable window regulator to suit all Spiders 1970-74 (left side window) with non-electric windows. Note that this regulator has a splined shaft length of approximately 30mm. Later regulators have a shaft length of approximately 40mm. Check yours carefully...

GT front wing right - for all step-front cars, best quality available. This is the same high quality front wing as sold for the late cars (made by the same company) but with the extra corner section for the early style wing with...

GT front wing left - for all step-front cars, best quality available. This is the same high quality front wing as sold for the late cars (made by the same company) but with the extra corner section for the early style wing with...

Grommet for the heater hose where it passes through the firewall. Fits all 105 series cars from 1968 onwards plus many 116 and 75 models.. Two are required for right hand drive cars, one for left hand drive cars that use a different combined grommet for...

Small rubber grommet for the holes that the under bonnet/hood wiring passes through on many of the 105 series cars. Also fits the rear valance panel where wiring for the rear numberplate lights passes through on many of the 105 Series cars as well.

Two piece rubber grommet for the accelerator/throttle lever through where is passes through the bulkhead on all left hand drive cars.

Oval rubber grommet for where the main wiring loom passes from the cabin into the engine bay on all 105 series cars.

Rubber grommet for the hole in the firewall where the scuttle drain hose goes through. Fits all 105, 115 and 116 series cars, including GTV6.

Remanufactured right tail light backing unit to suit all GTs & GTVs up to and including 1750 models and late GT Juniors. Includes all the bulb holders and connectors to match your exisiting wiring.  See LT074 to see the matching unit for the left side...

Remanufactured left tail light backing unit to suit all GTs & GTVs up to and including 1750 models and late GT Juniors. Includes all the bulb holders and connectors to match your exisiting wiring.  See LT075 to see the matching unit for the right side...

Complete Carello branded right rear light unit, including seal, reflector and plastic body to fit all GTs, GT Juniors and 1750 GTVs.

Complete Carello branded left side rear light unit, including seal, reflector and plastic body to fit all GTs, GT Juniors and 1750 GTVs.

Rear reflector for early type rear lens - 1964-1971 GT / GTV and all GT Junior 1966-77 (except South African Juniors with large rear lights). Dimensions: Studs (centre to centre distance) - 49mm Height - 44.5mm Width - 70.4mm Thickness - 9.7mm

Rear lens GT / 1750GTV / GT junior, pattern part with moulded in reflector, right

Rear lens GT / 1750GTV / GT junior, pattern part with moulded in reflector, left

1750GTV/GT junior/early GT rear lens, Carello - right. Reflector available separately (LT097)

1750GTV/GT junior/early GT rear lens, Carello - left. Reflector available separately (LT097)

2000 hubcap badge. Fits into the polished 'spinners' that are on 2000 GTVs, late GT Juniors, Spiders and later Saloons.    

Exhaust tailpipe o-ring for the joint between the centre and rear sections of the exhaust on all 105 series cars

Front anti-roll bar end bush. Fits into drop link between the bar and the spring pan. Some Spiders from about 1978 to 1986 use a larger 33mm bush in this link. This is the larger bush. Standard sized 30 mm bush for earlier cars is available under code...

Rear anti-roll bar lower bush. Fits into the lower end of the long vertical arm from the bar to rear trailing arm bolt. Originally there were two different bushes for the upper and lower (the lower one having a slot in each side of the inner metal...

Superflex 29mm front anti-roll bar bushes to suit the large anti-roll bar we supply as part of the handling kit. Fits into the bracket at the front of the chassis rails. Two bushes required per car, sold as a pair.