Categories

High performance 80W/140 Fully Synthetic gear oil formulated with high levels of extreme pressure (EP) additives and friction modifiers to protect the critical mechanisms of limited slip differentials. In addition to high load carrying capability,...

Plastic profile moulding that fits around the edge of the guard inside the fuel flap to protect it from damage from the fuel filling hose. Often missing on most cars! Use in conjunction with the two small rubber buffers available under code MI016 that...

Pertronix high performance ignition coil. Black body, 3 ohm, around 40,000 volt output. For standard and fast road engines - Ideal for use with the Pertronix Electronic Ignition kits available separately. For full race engines we sell...

New production of washer foot pump to replace the often unreliable originals! Fits all 105 Series cars including Montreal. The plastic tubing that fits this pump is (WI025)    

1300 GTA GROUP 5 NURBURGRING 1972 - Printed on quailty art paper 39" x 26" (99 x 66 cm)

105.29 body type plate for the rare right hand drive version of the Giulia GTC convertible.

Mounting bracket for all Bertone GT/GTV outer door handles 1964-1977. Two required per car.

GT outer door handle seal. Not an original fitment to the cars when new, but a popular addition nowadays to protect the paintwork around the door handle opening and reduce water ingress to the doors. Sold individually, two required per car.

Pair of outer door handles to suit all GTs, GTVs, GTCs and GTAs with matching keys. Made from the original tooling. See also CH016/1 for the metal support bracket to attach the handles to the door.

Outer door handle to suit all GTs, GTVs, GTCs & GTAs 1964-77 - right side. Made from the original tooling. See item CH013 for the matching item for the left side door, or code CH015 for a pair of handles. Also see CH016/1 for the metal retaining braket...

Outer door handle to suit all GTs, GTVs, GTCs & GTAs 1964-77 - left side. Made from the original tooling. See item CH014 for the matching item for the right hand door, or code CH015 for a pair of handles. Also see CH016/1 for the metal retaining braket...

Rear exhaust pipe section without a silencer/muffler - for a more sporting exhaust note! Made in Italy by IMASAF - OE Quality steel exhaust systems since 1954! LHD RHD: Fits all GTs/GTVs and Giulia saloons up to 1978. Please...

Pipercross filter socks - set of 4 for those with GTA style intake trumpets fitted or similar rampipes.

Pipercross 40 DCOE rampipes set - sold as a set of 4 only. Will fit Weber, Dellorto and Solex carbs fitted to 105 series Alfas. Depth -30mm

Pair of Pipercross kk300 air filters - inc. mounting plates. No rampipes necessary. ** NOTE ** - the backplate may need some easy trimming to make it fit some engines.

Pipercross kk600 air filter - including mounting plate. Fixes directly over both carbs. Greatly improved induction, can be teamed with rampipes available under code FL045 for best effect. ** NOTE ** - This is not suitable for 1300 engines in...

Pair of K+N 'pancake style' performance air filters to suit all sidedraught twin carburettor Alfas. Chrome plated bodies and long-life filter elements and all fittings included. Not suitable for 1300 engines. 

Differential pinion outer (front) bearing to fit the smaller pinion shaft found in 1300-1750cc engined cars, also fits some late 101 series cars. If you have a 101 Series car please measure your bearings and compare between this bearing and...

Rear layshaft bearing (inside diameter 30mm, outside 62mm, width 16mm) to suit hydraulic clutch gearboxes.

Layshaft rear bearing to suit mechanical clutch 105 series cars. Also fits 5 speed 101 series, late 102 series and all 2600 (106 series). Outer diameter - 62mm Inner diameter - 30mm Thickness - 16mm

Spring to fit all 105 Series hydraulic clutch release bearings 1968-1993.

Top timing chain to fit all 1750 and 2000 engines. Not TS.

Pair of 56mm mesh filters, to suit rampipes fitted to 40 DCOE carburettors. 

Pair of 63mm mesh filters to suit rampipes fitted to 45 DCOE weber carburettors. Will  fit on the rampipes supplied with new 45 DCOE carburettors. One set per carburettor.