Categories

2MM bush to suit 101 series steering idler boxes. Will also fit later 750 series cars, approximately 1958 onwards. Bush approx. 24mm ID and 28mm OD. These bushes need reeming to suit your existing pin. Also used on 2000/2600. You need to order two bushes...

Repair section for the top of the right rear wing under the side window. A common place for these cars to rust! Fits all GT / GTV - 1964-77.

Repair section for the top of the left rear wing under the side window. A common place for these cars to rust! Fits all GT / GTV - 1964-77.

New production from the original manufacturer of top quality gearbox synchro rings to fit later 105 Series gearboxes, as well as later Alfetta and 75 based cars - including V6 versions. The best synchro rings available for your gearbox, produced in...

105.05 Body type plate to fit a right hand drive 1600 Roundtail Spider 1966-67.

Correct original style allen headed screw to fit the steering column shroud/cover on most 105 Series cars (but not Montreal). Sold individually. Usually the column shroud/cover has a combination of two 'short' and three 'long' screws - which are...

Correct original style allen headed screw to fit the steering column shroud/cover on most 105 Series cars (but not Montreal). Sold individually. Usually the column shrouds have a combination of three 'long' screws and two 'short' screws - which are...

105.03 body type plate to fit left hand drive 1600 Roundtail Spider 1966-67.

Special sized brake disc (265mm OD) to fit 1966-67 model year cars with early ATE front brakes, mainly 1600 Roundtail Spiders and 1600 Sprint GT Veloce models.

Water pump seal to fit 1300cc 750 & 101 Series engines, 1900 engines, 102 Series 2000 engines and 106 Series 2600 engines.

Set of 4 high quality (Payen brand or similar) valve guide oil seals to fit 8 mm diameter valve stems on 75 twinspark and 750-series engines.

Valve spring retainer to fit performance valves with 8mm stem diameters. Sold individually.

Inlet valve guide to match the performance valve with 8mm diameter valve stem available under item code EN589.

Valve guide to fit FIA specification GTA inlet valves with 8mm stem diameter. Please note that original GTA valves were 8.5mm stem, we use an 8mm valve as it will improve intake flow.

Valve guide to fit FIA specification GTA exhaust valves with 8mm stem diameter. Please note that original GTA valves were 8.5mm stem, we use an 8mm valve as it will improve exhaust gas flow.

Valve guide to fit performance valves with 9/32" diameter valve stems. Can be used on both inlet and exhaust valves.

Rubber/metal/plastic steering column joint to suit right hand drive 2600 cars.

Rubber section that seals around the edge of the radiator aperture in the bodywork on all 105 series GT & GTV, Spider and Saloons from about 1967 onwards where the radiator sits on a rubber support (available under item code WA050) on the front...

Engine oil pump to suit both 1300 and 1600cc 101 series engines. Does not include the pickup pipe.

Magneti Marelli style distributor cap and ignition rotor kit to suit 8 plug GTA distributor with 10mm shaft, usually found on 1300 GTAs and some 1600 cars.

Brake master cylinder seal kit to suit 3/4" (19mm) master cylinders as fitted to 101 Series cars with front disc brakes.

105.26 body type plate to suit left hand drive 1600 Giulia Super saloons made from 1965-1972

The classic Zagato 'Z' badge as found on Zagato bodied cars for many years, including the Junior Z, Giulietta SZ and Zagato bodied 1900 models as well.

Two piece Junior Z rear script badge to go on the rear of 1300 Junior Zagato coupes.