Categories

Later style valve/cam cover hold down bolt with the large flats suitable for use with a 17mm spanner. Fits 4 cyl 105, 116 and 75 engines.

Chromed bolt suitable for holding down the cam cover on all twin-cam 101 and 105 series cars. In the original style with the serrated edge and large allen key socket. 6 bolts per car.

Door lock barrel and key set for all Spiders with 'flush' door handles 1970-1993. Also available as individual key & barrel under code CH036. 

Reverse light switch which screws into the bellhousing on later gearboxes with short selector rods, generally found in Series 3 and Series 4 Spiders. See GB049/1 for the earlier version with a mounting bracket that attaches to the bellhousing.

Front valance/apron panel for all Giulia saloons covering the area underneath the front grille downwards.

Vinyl covered inner door trim panel capping to suit all Spiders 1983-87 - right side. See IN080/2  for the matching part on the left hand side. Not suitable for late S3's from 1988-1989, please see IN271 See IN080 & IN080/1 for the earlier style moulded...

Vinyl covered inner door trim panel capping to suit all Spiders 1983-87 - left side. See IN080/3  for the matching part on the right hand side. Not suitable for late S3's from 1988-1989, please see IN270 See IN080 & IN080/1 for the earlier style moulded...

Beautifully reproduced enamel Touring 'wings' badge. 50mm long with one single mounting on the rear. Fitted to the 2600 spider front wings.

Inlet manifold gasket to suit the 2600 engine.

Rubber camshaft/valve cover gasket for all 2600 engines.

Heater hose grommet for Stepfront Sprint GT, Sprint GTVs, GTAs, GTCs, Roundtail Spiders and Giulia sedans up to the late 1960s. Also fits many 116 and 75 models. Sold individually. 

Rubber firewall grommet for left hand drive cars that takes the heater hose and speedometer cable and hand throttle cable on later cars. Fits left hand drive cars up to mid 1970s.

Small rubber grommet that fits in the hole in the firewall/bulkhead where the bonnet/hood release cable passes through from the interior of the car.

Rubber seal for the leading edge of a Step-front bonnet (hood). Glues to the underside of the leading edge of the bonnet/hood and seals against the top of the front bodywork. 

Heavy duty 27mm front anti-roll bar bushes to suit larger diameter anti-roll bars. Sold as a pair

Vented GTAm style front brake rotor. Approx. 250mm diameter and 22mm thickness. To be used with special GTAm brake calipers available under code GTA201.

1600 badge for rear of 101 Series Giulia Spider

Set of 4 radiator support rubbers to suit 1900, 750, 101 and 106 Series cars.

Pair of outer door handles to suit all 750 & 101 Series cars - as well as some Ferrari & Lancia models as well. Note that the key is the left side door handle.    

Complete interior courtesy and underbonnet light unit to suit 750 & 101 Series Sprints and Sprint Speciales.

Left hand front wheel brake cylinder for 2 shoe front brake systems on 750 and early 101 Series cars. Note that there are two cylinders in each front brake and that the cylinders are different left to right- right available under 750-014/1.

Rubber bush for gearbox to exhaust hanger (2 per car). Fits 750 & 101 series cars, as well as 1900s, 102 series 2000 & 106 series 2600 cars as well. Outer Diameter - 54mm Inner Diameter - 16mm Edge width - 22mm Center width - 28mm

Full set of ignition points (2 pairs) to suit the Marelli S127 C distributor.

Spider door buffer - right side door. Fits all Spiders 1966-93. See RB060 for the same part for the left side.