Categories

Rear wheel bearing kit - bearing and oil seal - to suit 1300, 1600 and 1750 cars until approximately 1974. Does not suit the 2000 style limited slip rear axle as that has larger diameter halfshafts. See item code SU023/1 for the equivalent part for the...

HT lead clamp, fitted to 105 series (not for early 105 series cars with screw in thermostat), 116 series and some 75s.

Soft top tensioning wire as fitted on all Spiders 1970-93. 2 required per car. The tensioner for adjusting this wire is available under code IN066/1.

Tensioner for soft top wire as fitted on all Spiders 1970-93. 2 per car. The wire is available under code IN066.

Spider Kammtail lower seat edging. Will cover both seats. 

Securon brand, static front 3 point seat belt - fits all saloons. These belts come with a 45cm long stalk to go against the transmission tunnel. If you want a 30cm stalk see part AC031

Static rear 3 point seat belt to fit all GTs/GTVs from 1964-1976.

Inertia reel rear seat belt to fit all GTs/GTVs and saloons 1964-1976.

Securon inertia reel front seat belt - fits all GT/GTV models. Note this belt has a 30 cm (12 inch) stalk to fit to the tranmission tunnel. If you require a longer stalk to fit your car (45cm) see item code AC032/1.

Securon brand static front 3 point seat belt - fits all GT/GTVs, Spiders and Montreal. These belts come with a 30cm (12 inch) long stalk to go against the transmission tunnel.

Complete Twin-Spark engine gasket set. Includes crank seals and REINZ head gasket.

Berlina 1750 & 2000 door handle backing plate.

Rubber strip to fit between the fuel tank and the surrounding bodywork, in the correct contour. Will fit all 105 cars   

OE quality rear wheel bearing kit - bearing, seal and shrink ring - to suit all limited slip axles (found in all 2000 cars) from 1972 onwards and all 1600 cars from 1975 onwards. One kit does one side of the axle, two required per car.  Note that the...

Complete Twin-Spark engine gasket set. Includes crank seals. No Head gasket included in this kit. if you require head gasket, please see kit EN510/1

Inlet valve to fit Alfa 75 style Twin Spark engines. Price is per valve.

Cylinder head overhaul gasket set for 2 litre Twin-Spark (75) engine. Includes Spesso head gasket along with all other required gaskets.

Rubber strip to fit between the fuel tank and the surrounding bodywork.

Window winder handle to suit all 2000 GTVs and later GT Juniors, 2000 Spiders and Saloons from 1972 up to about 1986, depending upon Spider trim variations. Also fits Junior Zagato. Same handle fits either side of the car. Remanufactured on the original...

Inner door handle to suit all 2000 GTVs and later GT Juniors, 2000 Spiders and Saloons from 1972 up to about 1986, depending upon Spider model trim variations! Same handle fits either side of the car. Remanufactured using the original tooling and...

Stainless steel Sport exhaust manifold to suit Twin Spark engines fitted into 105 Series cars, either Saloon, Spider or Coupe.

Rear wheel bearing kit - bearing, seal and shrink ring - to suit all limited slip axles (found in all 2000 cars) from 1972 onwards, as well as all 1600 cars from 1975 onwards. One kit does one side of the axle, two required per car. See item code SU023...

New rubber boot (trunk) mat that covers the vertical section behind the rear lights and fits under the stainless edging trim. Done in grey in the correct original style and pattern. See item code IN062/1 for the same item in black rubber.

Main GT boot (trunk) floor mat in grey rubber, produced in the correct original size and style. Includes moulded in logo as per original.