NEW PRODUCTS

Wosp Performance, lightweight starter motor to suit all cars with an 8 tooth pinon starter and 3 bolt mounting. This will fit all 1300/1600/1750 engines from 1968-74 and can also be used on early cars from 1960-67 with a two bolt mounting. ** NOTE ** -...

Wosp Performance, high torque starter motor to suit all cars with a 9 tooth pinon starter and 3 bolt mounting. This will fit all 2000 engines from 1972-93 (105, 115 116 Series). As well as late 1600 cars with a 9 tooth starter. ** NOTE ** - If...

Wosp Performance, high torque starter motor to suit all cars with an 8 tooth pinon starter and 3 bolt mounting. This will fit all 1300/1600/1750 engines from 1968-74 and can also be used on early cars from 1960-67 with a two bolt mounting. ** NOTE ** -...

New production of the chrome gear lever gaiter frame that fits Giulia saloon with centre consoles. Excellent quality.

Sprint 750 & 101 door check strap. Please note some 101 cars have a different type of check strap.

Seat base foam to suit all MK1 1750 GTV (1968-69).

Misab carburettor washer set to suit cars with solid carb mounts. These gaskets will do 40mm/45mm/48mm carbs and are compatible with Webers, Dell'orto Solex.

Spider door glass in the original green tint as used on Series 4 Spiders. This glass can be used on spiders from 1970-93 however earlier cars would have had a bronze tint (S3 Spiders) or clear glass (S2 Spiders). If you require the clear glass, as used...

Halfshaft oil seal to suit all Alfetta GTV/GTV6/75/75V6 cars, as well as SZ & RZ

Narrow focus Carello rear number/licence plate light unit as used on late 750 all 101 Series cars. Require a 207 bulb - our part number LT085.

Bumper, overrider spacer block to suit all GTs with overriders from 1970 onwards. This block is suitable for the front left or the rear right overrider. If you require the front right and rear left please see CH134

Bumper, overrider spacer block to suit all GTs with overriders from 1970 onwards. This block is suitable for the front right or the rear left overrider. If you require the front left and rear right please see CH133

10K Boost E10 Fuel Protector is an all in one fuel treatment forvehicle that require ethanol corrosion protection and valveseat lubrication and protection. In addition it boosts the fuelsoctane number.Ethanol based fuels tend to lubricate less and...

Carello style yellow, H1 bulb, inner headlight that goes on the left hand side (looking from the driving seat) of all 4 headlight Giulia saloons. This lamp uses the mounting/locating style with two lugs on the headlight body, one on the...

Bosch starter motor, 3 bolt mounting and 8 tooth pinion to suit 1300/1600/1750 engines. ** NOTE ** - If your vehicles is a 1600 from 74 onwards, it may have a 9 tooth starter motor. Please count the teeth on your old starter carefully before...

New production of the wood steering wheel centres found on mk2 1750 GTV steering wheels. This centre is made from solid piece of wood, finished in lacquer to bring it to a deep shine.

Full set of rear Brembo brake discs & pads with pin & spring set. Cars with ATE calipers.

Full set of front Brembo brake discs & pads with pin & spring set. Cars with ATE calipers 1750/2000.

Montreal rear windscreen, light green tinted and embedded heating elements as original.

Original style rear spoiler kit for series 3 Spiders from 1984-89. This kit comes in black and contains 3 pieces.

Current production of the classic Weber 45 DCOE performance carburettor with 5 progression holes. Sold individually. Requires an extra linkage kit and fuel union available separately under part numbers FL064 & FL065 to fit as a pair. Air...

Oversize (14.10mm) inlet valve guide to fit all 4 cylinder 101, 105, 116 and 75 engines - plus Montreal - with 9mm valve stems. Not TS. Sold individually. Note, these can also be used as an exhaust valve guide if you wish to fit valve stem seals on...

HT lead cap for distributor end. Will fit 7mm 8mm HT leads

Shim kit for Burman steering box, for both left and right hand drive cars. Stainless steel set including end bearing cup and top plate shims.