Categories

A pair of interior sun visors to fit all GTs (Interior mirror on right side visor). Includes pivots. Black on both sides.

A pair of interior sun visors to fit all GTs (Interior mirror on right side visor). Includes pivots. Black on one side of the visor and cream on the other to match the headlining.

Clutch cable to fit all right hand drive 105 Series cars with mechanical operated clutches.  

Endless bottom timing chain to suit all 4 cylinder 750, 101, 105, 116 and 75 engines, including TS.

Rear ashtray support brackets to suit all 105 series GTs. This is the bracket that holds the rear ashtrays into the rear interior panels. Two required per car.

Famous lightweight Gripper limited slip race differential unit for 105 non-LSD rear axles fitted with larger halfshafts. Note, most non-LSD axles have smaller halfshafts and would need our Gripper diff GB070. The legendary Gripper unit now made to our...

Armrest support plate. Suitable for GT 1300, 1600 & 1750 (with plastic door handles) & Giulia saloon 1300, 1600. Will do both right and left door. Please note early GTs with foam door armrest were fitted with the straight studs not angular...

Handbrake lever spring. Suitable for 1900/750/101/102/106 series cars. 

Upper distributor cowling clip. If you also require the upper clip, please see part IG028.

Wiring loom to suit a left hand drive Touring bodied 2600 Spider. PVC wires with PVC sleeving. Product images are for illustrative purposes only and may differ from the actual product.

Distributor cowling clip. If you also require the lower clip, please see IG028/1

Rear exhaust pipe section including muffler and chrome exhaust tip, to suit all Berlina saloons, 1750 & 2000 both left and right hand drive. Made in Italy by IMASAF - OE Quality steel exhaust systems since 1954! Please see EX023 for...

Handbrake lever buffer. See second pictures for fitting position.    

Rear exhaust pipe section including muffler, to suit all 1300 Junior Zagato. Made in Italy by IMASAF - OE Quality steel exhaust systems since 1954! Uses EX023 EXHAUST TAILPIPE O RING

Famous lightweight Gripper limited slip race differential unit for all 105 2000 LSD rear axles. The legendary Gripper unit now made to our own lightweight specification (machined to the same lightweight profile as used by racing Jaguars with 500hp...

Handbrake lever button.  Please note the pilot hole has been drilled, but will require finishing by customer for the correct pin diameter (it is made as a low volume 3D printed part). 

Wiring loom to suit a right hand drive Touring bodied 2600 Spider with pvc wires/sleeving. Product images are for illustrative purposes only and may differ from the actual product.

Small brake servo overhaul kit containing the vacuum valve and seal to fit the Lockheed brake servo/booster fitted to early 1750 cars with single circuit brakes. For a fill overhaul kit, see item code BR005.

Complete car set of door handle rubber seals to fit the larger door handles on later Giulia saloons.

Set of 4 door handle rubber seals to fit the smaller door handles on earlier Giulia saloons.  

Rubber mat set to fit 750 and 101 Series Sprint Speciales. Consists of two heel mats and boot mat. Reproduced in the correct original style.

Wiring loom to suit a left hand drive 1958-1962 Touring bodied 2000 Spider. PVC cables with correct style connectors and PVC outer sleeves for protection. Please note this loom doesn't include the black wired cable for the instrument bulb holders...

Rubber buffer to fit onto the end of the bonnet/hood support stay on 750 & 101 Series Spiders and all Stepfront Coupes and the boot/trunk support stay on all 750/101 Spiders as well as Giulia GTCs and GTAs.

Oil sandwich plate kit to suit post '72 'spin-on' style oil filters. Includes sandwich plate and rubber hoses. Use in conjunction with one of the 13 row oil coolers available under item code EN570 (115mm) or EN571 (235mm).  See item code EN574 for a...