GTA RACE & PERFORMANCE PARTS : BODY PANELS

Carbon fibre left door to suit late 105 series GTs/GTVs with cable style window regulators. If you are looking for a super lightweight alternative to your current steel doors, whilst also retaining the strength and rigidity of a steel panel. Then...

Carbon fibre right door to suit late 105 series GTs/GTVs with cable style window regulators. If you are looking for a super lightweight alternative to your current steel doors, whilst also retaining the strength and rigidity of a steel panel. Then...

Carbon fibre bonnet to suit 105 series stepfront GTs. If you are looking for a super lightweight alternative to your current steel bonnet, whilst also retaining the strength and rigidity of a steel panel. Then look no further. This carbon fibre...

Carbon fibre boot lid to suit all 105 series GTs & GTVs. If you are looking for a super lightweight alternative to your current steel boot lid, whilst also retaining the strength and rigidity of a steel panel. Then look no further. This carbon...

Lightweight fibreglass spare wheel well to suit all 105 series cars. For competition use.

Fibreglass half fuel tank to be used on 105 series cars that have competition, in boot, fuel tanks fitted, in place of the original fuel tank. This part provides the support for the boot floor needed when the original fuel tank is removed and also serves...

Lightweight aluminium GTA stepfront bonnet. This bonnet will fit all stepfront GTs.

Nice quality GTA/Stepfront front panel in aluminium. Stamped from a tooling, not a handmade approximation! Requires the two oval holes to be cut out under the main grille apeture to match original GTA panels. 

105/115 series engine compartment strengthening panels. These panels fit in the area behind where the steering box and idler mount on the outside of the inner wing. Providing extra support and strengthening whilst also cutting down on unwanted body flex...

Remanufactured aluminium right front wing. Stamped from the same tooling as our early GT front wings with correct profile around the sidelight for the "step-front" cars.

Remanufactured aluminium left front wing. Stamped from the same tooling as our early GT front wings with correct profile around the sidelight for the "step-front" cars.

All aluminium GTA wiper / scuttle panel. Will also fit GTs & GTV for a weight saving over the original. For the standard steel item see ST263.

Aluminium GTA door skin - right side of car

Aluminium GTA door skin - left side door

Complete right side aluminium rear wing/fender. Stamped from accurate tooling - not a hand-made approximation. Uses the correct early style arch profile as used on original 1600 GTA models 1965 to 1967

Complete left side aluminium rear wing/fender. Stamped from accurate tooling - not a hand-made approximation. Uses the correct early style arch profile as used on original 1600 GTA models 1965 to 1967.

Complete right side aluminium rear wing/fender. Stamped from accurate tooling - not a hand-made approximation. Uses the later higher arch profile (post 1967) as used on 1300 GTA style cars - provides better wheel/tyre clearance.

Complete left side aluminium rear wing/fender. Stamped from accurate tooling - not a hand-made approximation. Uses the later higher arch profile (post 1967) as used on 1300 GTA style cars - provides better wheel/tyre clearance.

Reproduction aluminium panel that covers the area between the rear screen and the top lip of the bootlid. Matches into the rear wings.

All aluminium GTA bootlid. Will also fit GTs & GTVs (but not Giulia GTCs). Huge weight saving - 2.5kg in weight as opposed to the 6kg of a steel bootlid!

Complete rear valance panel in aluminum to suit GTAs.

Fabricated aluminium plinth to take the correct style numberplate lights (available under item code 750-311) to suit bumperless GTAs and GTA replicas.

Set of 4 fibreglass wheel arch extensions to suit GTAm/GTA Group 5 'widebody' replicas. These will fit early "step-front" cars as well with minor modification - see last photo - it is our performance parts demonstrator bodyshell fitted with these arches...

Beautifully made lightweight carbon bonnet/hood to suit non-Stepfront style cars.