Categories

Handbrake lever spring. Suitable for 1900/750/101/102/106 series cars. 

Upper distributor cowling clip. If you also require the upper clip, please see part IG028.

Wiring loom to suit a left hand drive Touring bodied 2600 Spider. PVC wires with PVC sleeving. Product images are for illustrative purposes only and may differ from the actual product.

Distributor cowling clip. If you also require the lower clip, please see IG028/1

Rear exhaust pipe section including muffler and chrome exhaust tip, to suit all Berlina saloons, 1750 & 2000 both left and right hand drive. Made in Italy by IMASAF - OE Quality steel exhaust systems since 1954! Please see EX023 for...

Handbrake lever buffer. See second pictures for fitting position.    

Rear exhaust pipe section including muffler, to suit all 1300 Junior Zagato. Made in Italy by IMASAF - OE Quality steel exhaust systems since 1954! Uses EX023 EXHAUST TAILPIPE O RING

Famous lightweight Gripper limited slip race differential unit for all 105 2000 LSD rear axles. The legendary Gripper unit now made to our own lightweight specification (machined to the same lightweight profile as used by racing Jaguars with 500hp...

Handbrake lever button.  Please note the pilot hole has been drilled, but will require finishing by customer for the correct pin diameter (it is made as a low volume 3D printed part). 

Wiring loom to suit a right hand drive Touring bodied 2600 Spider with pvc wires/sleeving. Product images are for illustrative purposes only and may differ from the actual product.

Small brake servo overhaul kit containing the vacuum valve and seal to fit the Lockheed brake servo/booster fitted to early 1750 cars with single circuit brakes. For a fill overhaul kit, see item code BR005.

Complete car set of door handle rubber seals to fit the larger door handles on later Giulia saloons.

Set of 4 door handle rubber seals to fit the smaller door handles on earlier Giulia saloons.  

Rubber mat set to fit 750 and 101 Series Sprint Speciales. Consists of two heel mats and boot mat. Reproduced in the correct original style.

Wiring loom to suit a left hand drive 1958-1962 Touring bodied 2000 Spider. PVC cables with correct style connectors and PVC outer sleeves for protection. Please note this loom doesn't include the black wired cable for the instrument bulb holders...

Rubber buffer to fit onto the end of the bonnet/hood support stay on 750 & 101 Series Spiders and all Stepfront Coupes and the boot/trunk support stay on all 750/101 Spiders as well as Giulia GTCs and GTAs.

Oil sandwich plate kit to suit post '72 'spin-on' style oil filters. Includes sandwich plate and rubber hoses. Use in conjunction with one of the 13 row oil coolers available under item code EN570 (115mm) or EN571 (235mm).  See item code EN574 for a...

New clutch cable for left hand drive cars with mechanically operated clutches.

Famous lightweight Gripper limited slip race differential unit for all 105 non-LSD rear axles Dunlop or ATE (the ones with small half shafts). The legendary Gripper unit now made to our own lightweight specification (machined to the same lightweight...

Rear section handbrake cable to suit 750 & 101 Series Sprints

Rear section handbrake cable to suit 750 & 101 Series Spiders

105.45 body type plate to suit right hand drive 1750 GTVs (Mk1 and Mk2), 1968-1972.

Brake servo repair kit to suit Benditalia / Bonaldi brake servos/boosters. This kit repairs the small vacuum air valve on the bottom of the brake servo unit. One kit per servo. See item code BR006 for the large kit to replace the main diaphragm in the...

Brake Servo repair kit to suit Benditalia / Bonaldi brake servos/boosters. This kit contains the large circular rubber diaphragm and seals for the cylinder. One kit does one servo/booster. See item code BR007 for a repair kit for the vacuum air valve...