Categories

Mounting screw to suit the hardtop support piece  (available separately) that sits behind the cockpit on all Spiders from 1970-93. Two required on each side - four in total per car.

New Spider 1970-89 hardtop mounting hook. Fits onto the hardtop support piece and held down with a screw (both available separately). Two required per car. Also used on 1989-93 Spiders to hold the hood bag/tonneau cover in place.  See CH080 and CH081 for...

New gasket for the top jet cover on all Weber DCOE carburettors.

Heater motor with fan to generally suit the later style heater unit found on 1750/2000 GTVs & GT Juniors and Giulia saloons from about 1968 onwards.  Note that different models changed heater units at different times. Spider generally use WA021/2 but you...

High performance race-spec clutch with rigid sintered fricton plate and lightweight steel flywheel set to suit 2000 engines with 6 bolt flywheels. Suitable for trackday and competition use. We use this set up in a 190bhp trackday car...

High quality performance valve springs from top UK manufacturer. Suitable for all 4 cylinder 101, 105, 116 and 75 engines including TS.

Genuine Weber top jet cover to suit all Weber DCOE carburettors. See item code FL071/1 for gaskets to match the cover.  

Beautiful quality reproduction rubber mat set for 750 & 101 Series Sprints 1955-63. Consists of two heel mats and boot mat done in the correct original style.

New chrome hard top support piece for all Roundtail Spiders 1966-69. Two per car - sits at the rear of the cockpit and the (optional) hardtop latches onto it.

Front exhaust section, made in Italy by IMASAF - OE Quality steel exhaust systems since 1954! LHD: Fits 1750 and 2000 Spiders 1971-1986 with hanging pedals and carburettors. Will also fit early 2000 Spica injected cars from 1971- 1975 and...

Front exhaust section, made in Italy by IMASAF - OE Quality steel exhaust systems since 1954! LHD RHD: Fits 1600 Roundtail Spiders, 1300/1600 Giulia saloons, Sprint GT/GTV/GTC, GT Juniors and Junior Zagatos with standing pedals to 1971. Please...

NOW IN STAINLESS STEEL - SO THEY WILL LAST FOREVER! Pair of metal brackets/strips for the rubber seal (available under code RB012) that goes down the outer edge of the 'B' post on all 105 Series Coupes. Replace the rusty metal strips on your car when you...

Rubber seal for the 'B' post outer edge on all 105 series Coupes. 2 required per car. See also RB013 for a pair of the metal mounting strips for this seal.  

Brake servo vacuum hose to fit all 105 Series cars with brake servos. RHD dual brake circuit cars and LHD dual circuit 1750s with standing pedals require two hoses. Can also be fitted on 2.0 116 cars. Dimensions: Length (from straight end to...

Electric aerial for Spider 1985-93. Dimensions: Total Height - 31cm Height to Mounting Surface (the portion that sits below the panel) - 28cm Widest Point - 10cm

Front exhaust section, made in Italy by IMASAF - OE Quality steel exhaust systems since 1954! LHD: Fits all 105-series coupes with hanging pedals. RHD: Fits 1750 GTV MK2 and all coupes from 1971. Please see EX027 for the corresponding...

Gearbox mainshaft rear bearing to suit hydraulic clutch gearboxes. Inside diameter 25mm, outside diameter 52mm, width 15mm.

Mainshaft rear bearing to suit mechanical clutch 105 series cars. Also fits 102, 106, 750 and 101-series cars but check sizes. Inside diameter 25mm, outside diameter 52mm, width 15mm.

Mechanical clutch pressure plate to suit 750, 101 and early 105 series cars. Use in conjunction with the friction plate available under item code CL015 and the release bearing and retaining clips available under item codes CL013 and CL013/1.

Mechanical clutch friction plate to suit 750, 101 and early 105 series cars. Use in conjunction with the pressure plate available under CL016 and the release bearing and retaining clips available under item codes CL013 and CL013/1.

Heater motor with fan. Approx.16.5cm diameter fan and a base fitting measuring 85mm (see photo). To fit the earlier style heater unit (pre 1968) found on Sprint GT/GTVs and 1600 Roundtail Spiders. Also used on early Giulia saloons 1963-67.

Complete side grille set (left and right) for 2600 Spider.

New original Bendix brake servo to suit all ATE RHD cars and LHD cars with standing pedals. If you require the unions, please click on the link below. You will require two per servo: - BR323 BRAKE UNION 3/8 UNF MALE

Plastic chrome edge trim for the 2000 GTV, 1750 & 2000 Berlina armrest. Please note, this differs slightly from the original type by having a self-adhesive backing. Also, please ensure surface is thoroughly cleaned before fitting.  Sold in 1 metre...