MONTREAL PARTS : OTHER BRAKE PARTS

Brake servo mostly fitted to GTV6 and 75 V6 models. Also fits RHD Montreal.

New production - pair of rear brake calipers to fit all Montreals.

New production - pair of front brake calipers to fit all Montreals. Also fits Ferrari 308 models as well! 

Keeping your brakes and calipers well-lubricated allows them to operate at peak performance for a smooth ride that is free from excess Noise, Vibration and Harshness. Apec brake grease is formulated from a copper-free lubricant that assists in the smooth...

ATE brake cylinder paste is used for repair, assembly and conservation of hydraulic brake components, It is applied thinly and evenly to cylinder sleeves, pistons and seals. (Assembly of Brake calipers, Master cylinder etc). - ATE brake cylinder...

Non-return valve for the servo as fitted to cars with hamging pedals.

Front RIGHT brake flexi hose bracket. To fit all 105 Series cars & Montreals. NOT SUITABLE FOR DUNLOP BRAKES

Front LEFT brake flexi hose bracket. To fit all 105 Series cars & Montreals. NOT SUITABLE FOR DUNLOP BRAKES

Goodridge braided brake line set (complete car set – 3 pieces). These stainless steel brake flexi hoses will improve the pedal feel and are guaranteed for life. This version is approved by the German TUV authorities and therefore suitable for the...

Brake flexi hose suitable for the following vehicles: All 105 series cars including Montreals (rear brake hose) All 750/101 series cars (rear brake hose) 2600 (106) cars (hydraulic clutch hose) ONE PER CAR! These hoses are compatible with 3/8...

Brake flexi hose to fit the front brake system (between brake lines and calipers/drums). Suitable for the following vehicles: All 105 Series cars (including Montreals) All 750/101 Series cars All 106 (2600) Series cars These hoses are compatible...

Short front copper brake pipe from the flexible line to the brake caliper on all Dunlop braked cars from 1964-66. 

Short copper front brake pipe from the flexible line to the brake caliper on ATE braked cars from 1968-93 with large front calipers (1750+2000 models) including Montreals.

Rubber grommet for the inner guard/wing where the hydraulic brake pipe passes through the metalwork. Two required per car - one on each side. Also fit Montreal bonnet emergency release cable and the grommets for the headlight vacuum pipe.

Bleed screw cap. Will fit all bleed screws.  

Brake disc/drum retaining screw.

Rubber plug brake master cylinder, 15mm diameter. Used to connect the reservoir to the master cylinder.

Rubber plug brake master cylinder, 20mm diameter. Used to connect the reservoir to the master cylinder.

Reservoir cap to fit the left hand drive clutch master cylinder reservoir. This cap will also fit the brake fluid reservoir on right hand drive 105 Series cars 1968 onwards and left hand drive cars 1968-70 with hydraulic clutch and single...

Large sized brake caliper bleed screw to fit 1750/2000 ATE front brake calipers.

Small sized brake caliper bleed screw to fit 1300/1600 small ATE front brake calipers and all ATE rear brake calipers.  

Caliper seal kit to fit all ATE rear brake calipers - one kit does two calipers. Note, if you are splitting the caliper apart, this kit does not include the small internal 'O' rings in the calipers. These are sold separately under item code BR086. 2...

Caliper seal kit to fit all ATE front brake calipers - one kit does two calipers. Note, if you are splitting the caliper apart, this kit does not include the small internal 'O' rings in the calipers. These are sold separately under item code BR086. 2...

Steel spring clip to fit the dust seals on the 38mm diameter piston ATE rear brake calipers fitted to all ATE braked 105 series cars from about 1967 onwards. Should be used in conjunction with the kits available under item code BR036 or BR082.2 required...