750-101 SPIDER PARTS : EXHAUST

Front exhaust section to suit 750 Series Sprint, Spider, Berlina Normales. Single 3 bolt flange and single downpipe. Made in Italy by IMASAF - OE Quality steel exhaust systems since 1954!

Front exhaust system to suit 750 Series and early 1300cc 101 Series cars with 4 bolt exhaust manifolds. Made in Italy by IMASAF - OE Quality steel exhaust systems since 1954!

'6 hole' front exhaust section to suit 101 Series Sprint & Spider Normales - both 1300 & 1600 versions. Made in Italy by IMASAF - OE Quality steel exhaust systems since 1954!

Complete 4 branch exhaust manifold to suit 750 and 101 Series 1300 Veloces. Made in Italy by IMASAF - OE Quality steel exhaust systems since 1954!

Replacement 1600 Veloce Spider & Sprint Speciale exhaust manifold. Made in Italy by IMASAF - OE Quality steel exhaust systems since 1954!

Short front exhaust and silencer for 1300 engined 750 & 101 Series cars. Made in Italy by IMASAF - OE Quality steel exhaust systems since 1954!

Complete centre and rear exhaust section to suit all 750 & 101 Series Spiders. Made in Italy by IMASAF - OE Quality steel exhaust systems since 1954!

Front exhaust section and silencer to suit 1600 Veloce Spiders and Sprint Speciales. Made in Italy by IMASAF - OE Quality steel exhaust systems since 1954!

Complete top quality ANSA exhaust system to suit 101 Series Normale Spiders with 6 bolt flange.  

Exhaust manifold nut to suit 101, 105, 116 and 75 engines, including V6. 8 fitted per cylinder head. These are a smaller outer diameter than the original which makes tightening easier as you have more access room around the nut.

Exhaust/inlet manifold stud 34mm to suit all 4 cylinder 101, 105, 116 and 75 engines, including TS. There are 8 on the exhaust side and 7 on the inlet side, of which three are longer and not currently available.   Please measure your existing inlet studs...

Copper cylinder head to exhaust manifold gasket to suit all 101 and 105 series engines plus 4 cylinder 116 models and 4 cylinder 75 engines (not TS).

Rubber hanger for the exhaust system on all 105/115 series cars. Normally two per car. Also fitted to 750, 101, 102 (2000) and 106 (2600) Series cars. Note. Metal plates and inserts for the rubber hangers are available under item code EX036.

Set of 2 metal plates and the insert for the bolt hole on the rubber exhaust hanger on all 105/115 series cars. Two sets are required for each hanger, usually 4 per car (2 rubber hangers). Also fitted to 750, 101, 102 (2000) and 106 (2600)...

Bracket for gearbox to exhaust hanger. Fits 750 & 101 series cars. Before purchasing please check Not suitable for Veloce and Berlina models. 

Bracket fitted from gearbox bracket to exhaust hanger. Fits 750 & 101 series cars. Before purchasing please check Not suitable for Veloce and Berlina models. 

Rubber bush for gearbox to exhaust hanger (2 per car). Fits 750 & 101 series cars, as well as 1900s, 102 series 2000 & 106 series 2600 cars as well. Outer Diameter - 54mm Inner Diameter - 16mm Edge width - 22mm Center width - 28mm

Brake master cylinder heat shield to suit all 750/101 Spiders.

Bracket which is bolted to pedal box casting, where the heat protection plate fixes on to it, protects the Brake master cylinder from heat generated by the exhaust system. 

Cylinder head to exhaust manifold gasket to 750 Series 1300 engines. 4 required per engine.

4 bolt exhaust gasket to fit the joint between the manifold and the downpipe on 750 and early 101 Series cars.

Exhaust manifold to downpipe gasket to suit 3 bolt flanges on 750 Series engines, 101 Series 1300 Spider Veloce and Sprint Speciales. Two required per car. Should also suit cars with single downpipe exhaust systems.   Center Bore Diameter: 45mm

Exhaust clamp to suit all standard sized (54mm) 750, 101 and 105 series exhaust systems. Usually one clamp per car, located on the join between the front and middle exhaust sections.