GTA RACE & PERFORMANCE PARTS : FUEL

Misab carburettor washer set to suit cars with solid carb mounts. These gaskets will do 40mm/45mm/48mm carbs and are compatible with Webers, Dell'orto Solex.

Blanking plate for use where you are using a GTA oil cap and therefore do not need the standard breather elbow.

Fibreglass half fuel tank to be used on 105 series cars that have competition, in boot, fuel tanks fitted, in place of the original fuel tank. This part provides the support for the boot floor needed when the original fuel tank is removed and also serves...

Classic Alfa 57 litre foam filled aluminium competition fuel tank designed to fit in the boot of a 105 Series GT or GTV while allowing you to carry up to two spare wheels - ideal for track days and rally cars. Designed by us as a development on...

VDO fuel gauge, to be used in conjuction with our competition fuel tank, FL040/1

Classic Alfa aluminium fuel filler neck.

Rubber style carburettor mounting kit (for a pair of carburettors) to suit cars that are using a solid alloy carb mount. This is a good alternative/upgrade to the regular thackery washers that are normally used.

Thackery washer, carburettor mounting. 5/16 - M8 fitting. 

Aluminium blanking plate to seal off the mechanical fuel pump mounting on 101 and 105 series cars with cartridge oil filter. This is used when fitting an electric fuel pump to the car.

Aluminium blanking plate to seal off the mechanical fuel pump mounting on carb equipped 101, 105, 116 and 75 models. This is used when fitting an electric fuel pump to the car.    

Set of 4 individual solid aluminium carburettor mounts to fit 40mm carburettors. Machined from solid aluminium and provided with gaskets on the carb side that have a built-in rubber seal to provide some absorption of engine vibration. Supplied with...

Viton fuel resistant rubber O ring to suit all solid carburettor mounts - as we have available under item codes FL017 and FL018. Ideal if you lose or damage an O-ring when fitting.

Carburettor rubber mount to suit 45mm carburettors. Sold individually, 4 required per car.

Solid aluminium 45mm carburettor mount set - 62 mm length to fit 45mm carburettors in black anodised finish.  Machined from solid aluminium then fitted with an O-ring on one face to provide both a seal and some absorption of engine vibration. Supplied...

Set of 4 individual solid alloy carburettor mounts to fit 45mm carburettors. Set includes 'O' rings , thackery washers and nylock nuts for the carb side plus plain nuts for the inlet manifold side. PLEASE NOTE, THE 'O' RING IS FITTED AGAINST THE...

Ball joint, for the throttle linkage, works in conjunction with FL052/1.

Bush for the throttle linkage mechanism arm. Also used on the clutch pivot arm on mechanical clutches. 

Bush for the throttle linkage mechanism where it pivots on the firewall/bulkhead. Two required per car.

Facet fuel pump mounting kit - suits both Silver Top and Red Top pumps. Consists of rubber mounting bushes and earth wire.

High performance 'Red Top' Facet electric fuel pump. Ideal for high horsepower carburettored racing cars. This latest variant now has solid state technology to provide superior reliability over the older points triggered types. The Interrupter fuel pumps...

Facet Silver Top low pressure electric fuel pump designed for use with carburettors. This latest variant now has solid state technology to provide superior reliability over the older points triggered types. The Interrupter fuel pumps can be fitted...

1/4NPT ninety degree elbow hose fitting to suit the Facet Red Top pump available under code FL063/1. Suits 5/16" or 8mm fuel hose.

1/8 ninety degree elbow hose fitting to suit the Facet Silver Top pump available under code FL063. Suits 5/16" or 8mm fuel hose.

1/4NPT straight hose fitting to suit the Facet Red Top pump available under code FL063/1. Suits 5/16" or 8mm fuel hose.