105 SALOON PARTS : USED PARTS

Used steering column grommet retaining plate for most right hand drive 105 Series GT/GTVs, Saloons and Spiders. These are quite hard to find and are a common part to corrode! We have a number of these plates so the one you receive may not be...

Used front bumper to suit late Giulia Saloons. This bumper is in good condition for its age, with only one small indentation that would sit completely under the overriders that would be fitted. This bumper just needs a polish up.

Used steering wheel to suit early 105 Giulia Saloons. This wheel is in good shape for its age with only a few small marks to the front and a couple of cracks to the bakelite.

Original, new old stock right side headlight mounting bracket to suit all Giulia saloons. This bracket is in good condition with a small amount of surface corrosion that would clean up nicely.

Used layshaft to suit all 1300/1600/1750 models from 1967-78.

The warm air duct bracket that sits under the carburettors attached to a hose to supply warm air to the airbox. Will fit any 105 car from 1970 onwards, this is a used part that has been media blasted and powder coated, as can be seen in the photos.

Used upper cylinder head bung plug to suit 101/105/115 Series engines. These bungs are used but still in usable condition. We have a number of these so the one you receive may not be the one photographed but will be of comparable condition.

Used rear cylinder head bung/plug to suit 105/115 Series engines. These bungs are used but still in usable condition. We have a number of these so the one you receive may not be the one photographed but will be of comparable condition.

Used cam sprocket to suit all 105/115 engines. These sprockets are used but are still in fully usable condition with no chipped teeth. We have a number of these so the one you receive may not be the one photographed but will be of comparable condition.

Used, original vapour blasted intake manifold to suit 101 series 1600 Giuliettas and some early 105 series cars with a single carb. This manifold has no corrosion at all, however there is some pitting to the casting and some of the studs and...

Used, original vapour blasted intake manifold to suit 101 series 1600 Giuliettas and some early 105 series cars with a single carb. This manifold is in great condition with no corrosion at all, some of the studs and fittings may want...

Used, original, vapour blasted, intake manifold to suit 101 series 1600 Giuliettas and some early 105 series cars with a single carb. This manifold is in great condition with no corrosion at all, some of the studs and fittings may want...

Used oil filter cannister. We are unsure as to what specific model this fits as there have been so many variations in sizes over the years so please check your current cannister dimensions against the dimensions below before ordering: Diameter -...

Used Alfetta 2000cc crankshaft. Currently around 020 undersize. Could also be fitted to a 105 series car if the crank were drilled to accept a spigot bush.

Used crankshaft from a 1300cc 105 series engine. Big end and main bearing journals are currently at 010 so it has plenty of scope for a re-grind, presumably to 020. Note, the journals have a coating of rust from storage.

Used crankshaft from a 2000cc 105 series engine. Big end journals are currently at 010 and main bearing journals are at 020. Note, the bearing journals have a coating of rust, as can be seen from the photos so a regrind to 020/030 would probably be...

Used crankshaft from a 2000cc Alfetta engine. Main bearing and big end bearing journals are both currently at 010 undersize. As well as 2 litre Alfettas, it will also fit 2 litre 105-series engines if the rear of the crank is drilled out to accept a...

Used crankshaft from a 2000cc Alfetta engine. Main bearing and big end bearing journals are still within STD measurements so it has never been re-ground. As well as 2 litre Alfettas, it will also fit 2 litre 105-series engines if the rear of the...

Used 1750 MK2 cylinder head. In good condition but it will need a skim because the mating surface has some scratches. 111.6mm thick approx. More photos upon request.

Used 1750 cylinder head. In good condition with only very light corrosion. 11.8mm thick. More photos upon request.

Used 1750 mk2 cylinder head. Dirty. Some corrosion to the mating surface, mainly around the coolant holes but very usable. 112mm thick so probably never reground. More photos upon request.

Used 1750 cylinder head in good condition. 112mm thick so probably never reground. More photos upon request.

Used 1750 cylinder head in good condition. 111.4mm thick. More photos upon request.

Used 1750 MK2 cylinder head. Dirty but in good condition. 111.8mm thick. No cam caps. Front bungs missing (but we can supply). More photos upon request.