105 SALOON PARTS : FUEL

Here is a diagram showing the location of some of the parts in this category.

Gasket, single carburettor.

Mechanical fuel pump to fit all carburettor-equipped 105 series cars plus 101 series 1300 and 1600 Normale cars. Mounting gaskets and plastic spacer blocks are available separately. This is a new production and the best quality we have so...

Gasket for the fuel pump mounted on the lower front timing cover on carburettored 101 Normale and 105 Series cars. There should be two gaskets fitted - one either side of the plastic insulating spacer block (available separately under item code...

Thackery washer, carburettor mounting. 5/16 - M8 fitting.

Plastic mounting spacer to suit mechanical fuel pumps mounted down on the front timing cover of the engine.

Aluminium blanking plate to seal off the mechanical fuel pump mounting on 105 series cars with spin on oil filter. This is used when fitting an electric fuel pump to the car.

Aluminium blanking plate to seal off the mechanical fuel pump mounting on 101 and 105 series cars with cartridge oil filter. This is used when fitting an electric fuel pump to the car.

Set of 4 individual solid aluminium carburettor mounts to fit 40mm carburettors but anodised in black to retain an original appearance to your engine bay. Machined from solid aluminium then fitted with an O-ring on one face to provide both a seal...

M8 X 1.25 NUT. Used on solid carb mounts (FL081) to attach to the inlet manifold.

Replacement Viton fuel resistant rubber O ring to suit all solid carburettor mounts - as we have available under item codes FL017 and FL018. Ideal if you lose or damage an O-ring when fitting.

Main engine bay fuel filter for Montreals and all 4 cylinder USA Spica injected cars. Also available as part of a set of Montreal fuel filters - see item code MN100.

Carburettor rubber mount to suit 40mm Weber, Dellorto and Solex carburettors. Used on all 105 series GT/GTV, Saloons and Spiders as well as 101 Series Veloce cars. Normally 4 required per car, but can be used in conjunction with the 'siamesed' mount...

Siamesed carburettor rubber centre mount and two individual to suit 40mm carburettors. This mount replaces the two separate central mounts and bridges between the two carburettors. These must now be sold as a set as they may be slightly different...

Carburettor rubber mount to suit 45mm carburettors. Sold individually, 4 required per car.

M8 x 1.0 nut. Fits the rubber carb mounts (FL014) used on most 105 series cars and the engine to bellhousing stud (EN135).

Earth strap to fit the carburettor mounts on all 105 Series carburettor cars. Often missing or damaged on many cars we see, ideal to replace when you fit new carburettor mounts.

40mm paper carburettor mount gasket to fit all 40mm Weber, Solex and Dellorto carburettor mounts. 2 required per rubber mount/carburettor throat.

45mm paper carburettor gasket,

Solid aluminium 45mm carburettor mount set - 62 mm length to fit 45mm carburettors in black anodised finish. Machined from solid aluminium then fitted with an O-ring on one face to provide both a seal and some absorption of engine vibration...

Set of 4 individual solid alloy carburettor mounts to fit 45mm carburettors. Set includes 'O' rings , thackery washers and nylock nuts for the carb side plus plain nuts for the inlet manifold side. PLEASE NOTE, THE 'O' RING IS FITTED AGAINST THE...

Rubber gasket filter for aluminium trough to air filter canister ('68-'78)

Gasket to fit between the air intake trough/plenum and the carburettor body on all carburettored 105 series cars fitted with side draught carburettors.

Gasket to fit the crossover style aluminium air filter housing fitted to all twin carburettor 105 Series cars 1300 to 1750 up to 1969. Fits between the lid and the body of the housing that bolts to the carburettors.