750-101 SPRINT SS Ti PARTS : ENGINE BLOCK

Standard con rod/big end bearings to suit 1600, 1750 and 2000 101, 105, 116 and 75 engines, including TS. Produced by an original equipment manufacturer such as Mahle or Vandervell and therefore favoured by performance engine builders. 

Main crankshaft bearings to suit all 1300 to 2000 101, 105, 116 and 75 engines. Produced by an original equipment manufacturer such as Mahle or AE Borgo  original suppliers to Alfa Romeo, and favoured by performance engine builders. 

Main engine crankshaft bearings - .030 oversize to suit all 101, 105, 116 and 75 engines 1300-2000cc.

Main engine crankshaft bearings - .020 oversize to suit all 101, 105, 116 and 75 engines, 1300 to 2000cc.

Main engine crankshaft bearings -.010 oversize to suit all 101, 105, 116 and 75 engines 1300 to 2000cc

Standard sized main engine crankshaft bearings to suit all 101, 105, 116 and 75 engines - 1300 to 2000. OE quality.

 Complete set of ACL or KING race quality STD conrod bearings. Due to supply being sporadic for these bearing, we will either supply ACL or the KING version. If you have a preference, please state this on the comments section when you place the order.  ...

Complete set of ACL or KING race quality conrod bearings +.010" oversize. Due to supply being sporadic for these bearing, we will either supply ACL or the KING version. If you have a preference, please state this on the comments section when you place...

 Complete set of ACL or KING race quality main bearings +.010" oversize. Due to supply being sporadic for these bearing, we will either supply ACL or the KING version. If you have a preference, please state this on the comments section when you place the...

 Complete set of ACL or KING race quality main bearings standard size. Due to supply being sporadic for these bearing, we will either supply ACL or the KING version. If you have a preference, please state this on the comments section when you place the...

Set of 010 oversized crankshaft thrust washers to fit all 101, 105, 116 and 75 engines, 1300-2000 including TS.

Little end/conrod to gudgeon pin bearing to fit 1300cc 101 and 105 Series engines.

Set of standard sized crankshaft thrust washers to fit all 101, 105, 116 and 75 engines, 1300-2000 including TS.

Set of 4 little end/conrod to gudgeon pin bearings to fit 101, 105, 116 and 75 engines, 1600, 1750, 2000 and V6 Busso engines. Also fits Montreal engines but note you'll need to order two sets for a full Montreal engine.

Aluminium crank oilway plug. 6 required per car.

Pointer front crankshaft pulley for top dead centre. Suitable for cracnk pulleys which are 125mm

Pointer front crankshaft pulley for top dead centre. Suitable for cracnk pulleys which are 105mm    

Flywheel to cranckshaft half moon fixings, to fit 8 bolt 101 & 105 series flywheels found on 1300, 1600 & 1750 cars.

Front crankshaft pulley nut to fit all 4 cylinder 101, 105 and 116 engines. Replace in conjunction with the tab washer available under item code EN112

Flywheel bolt to fit 8 bolt 101 & 105 series flywheels found on 1300, 1600 & 1750 cars. See item code EN100 for bolts suitable for 2000 6 bolt style flywheels.

Conrod nut to fit all 105 Series 1600, 1750 and 2000 engines including TS plus 101 1600 engines. Not for 1300.

Speedometer cable to suit all 750, 101, 102, 106 Series cars. 220cm long (just over 7 feet). We do keep a shorter 185cm cable (just over 6 feet) which may fit some models better - search part number EN087.

 Crankshaft front pulley bolt. Giulietta & Giulia 101 series

 Crankshaft front pulley bolt lock-tab. For 101 series cars where is bolt is fitted to the crank, not a nut.