The cookie settings on this website are set to 'allow all cookies' to give you the very best experience. Please click Accept Cookies to continue to use the site.

116-ALFETTA PARTS : OTHER 4 CYL BLOCK PARTS

  • PRODUCTS PER PAGE
  • AC130 ATHESIL RTV SILICONE SEALANT   80ml

    AC130 ATHESIL RTV SILICONE SEALANT 80ml

    Athesil RTV silicone sealant. A premium sealant/ gasket maker developed by Athena for professional use in engine maintainace and repair. The RTV (room temperature vulcanizing) silicone seals plastic metal componants, crankcases, manifolds ...

    £6.50
  • EN117 CONROD BOLT & NUT SET - 1750/2000

    EN117 CONROD BOLT & NUT SET - 1750/2000

    Conrod bolt nut set, to fit 105, 116 and 75 1750/2000 engines, including TS. Can be used on 1600 cars but the shoulder part doesn't sit centrally on the two conrod halves.

    £150.00
  • EN119 CRANKSHAFT FRONT PULLEY NUT

    EN119 CRANKSHAFT FRONT PULLEY NUT

    Front crankshaft pulley nut to fit all 4 cylinder 101, 105 and 116 engines. Replace in conjunction with the tab washer available under item code EN112

    £9.00
  • EN100 FLYWHEEL BOLT - 6 HOLE FLYWHEEL

    EN100 FLYWHEEL BOLT - 6 HOLE FLYWHEEL

    New bolt to fit all 6 bolt hole flywheels 1600-2000cc. Sold individually. See item code EN099 for bolts to fit 8 bolt flywheels.

    £4.50
  • EN082 CONROD BOLT - 1750/2000

    EN082 CONROD BOLT - 1750/2000

    Conrod bolt to fit 105 and 116 series 1750/2000 engines including TS, can be used on 1600 cars but the shoulder part doesn't sit centrally on the two conrod halves.

    £15.00
  • EN131 1750/2000 CYLINDER HEAD STUD

    EN131 1750/2000 CYLINDER HEAD STUD

    Cylinder head stud to suit 1750 & 2000 cc engines. 10 per engine if you are replacing them all.

    £19.95
  • EN130 1600 CYLINDER HEAD STUD

    EN130 1600 CYLINDER HEAD STUD

    Cylinder head stud (246mm long) to fit 101, 105 and 116 Series 1600 engines.

    £17.95
  • EN135 BLOCK TO BELL HOUSING STUD (HYDRAULIC CLUTCH CARS)

    EN135 BLOCK TO BELL HOUSING STUD (HYDRAULIC CL…

    Stud for the rear of the engine block to attach the bell housing of the gearbox on all hydraulic clutch 105 twin-cam engines. 4 studs used in total. For the relevant nut, see part FL109.

    £3.95
  • EN170 BUSH ENGINE BLOCK

    EN170 BUSH ENGINE BLOCK

    Bush engine block. Height is 17.5 m. locates the lower pulley in the block. MUST BE HONED 1300,1600 & 1750 engines.

    £12.00
  • EN091 SUMP PLUG WASHER

    EN091 SUMP PLUG WASHER

    Sump plug washer for most 750/101/102/106/105 series twin-cam engines. We supply copper or aluminium depending on availability from our suppliers - both work equally well. We recommend you replace any crush washer once it has been used more...

    £0.75
  • EN059 OIL SUMP PLUG (WITH MAGNET)

    EN059 OIL SUMP PLUG (WITH MAGNET)

    Oil sump plug to suit all 4 cylinder 750/101/106/105/116 series engines. Includes inbuilt magnet to keep unwanted debris out of your oil! Copper washers to fit the sump plug are also available under item code EN091.

    £8.50
  • EN175/1 BELL HOUSING TO BLOCK SPACER PLATE

    EN175/1 BELL HOUSING TO BLOCK SPACER PLATE

    Spacer plate for bell housing. Please check photo carefully, to make sure this part is correct for your vehicle. This spacer is generally fitted on later cars from 1983 onwards. If you require the starter motor spacer, please...

    £42.00

Follow Us @classicalfaltd