105 SPIDER PARTS : OTHER FUEL SYSTEM PARTS

Carburettor rebuild kit to suit Solex 40mm ADDHE carburettors - kit does 2 carburettors.

Carburettor rebuild kit to suit Weber 40 DCOEs - kit does 2 carburettors

Fuel hose clip to suit all Alfa fuel lines (usually 7mm internal diameter).

Fuel hose (8mm internal diameter) to suit all carburetted cars. Priced per metre (100 cm).

Accelerator cable to suit all LHD injection Spiders 1987-93.

Hand throttle cable stop.

Hand throttle cable to suit all carburetted Spiders 1970-87 with the cable mounted in the centre console. The cable is a solid wire and provided with an extra end piece in case lenght adjustment is required. May also fit Gt Juniors with hand...

Choke cable for all GTs/GTVs, Saloons and Spiders that have the choke lever mounted on the dashboard. Not suitable for 1750 & 2000 Spiders that have the choke mounted on the centre console. See FL025 for that part.

Choke cable to suit all carburetted Spiders 1970-87 with the choke cable mounted in the centre console. The replacement choke cable for other models is available under item code FL036. The cable is a solid wire and provided with an extra...

A cheaper alternative to the original BOSCH fuel pump that we sell under FL028.  External fuel pump to suit Bosch fuel injected Spiders, GTV6 and 75.  Note that there is also a lift pump located inside the fuel tank which is available under item code...

Rubber seal to fit into the original engine bay Fispa fuel filter/pressure regulator unit fitted to 750, 101 and 105 Series cars. This filter unit uses the smaller 3.3cm diameter filter FL005. Dimensions, outside diameter 53mm,and inside diameter 41mm.

BOSCH External fuel pump to suit Bosch fuel injected Spiders, GTV6 and 75.  Note that there is also a lift pump located inside the fuel tank which is available under item code FL028/1. Not suitable for the 1.8 Turbo 75

Fuel filter element - larger size, fits into the metal housing found on some later carburetted cars (1975 to 1986) as well as the Filter King fuel filter unit available under code FL053. Dimensions: Height - 4cm Diameter - 4 cm

Fuel filter element small - Fispa type fits in small glass bowl as used on most Alfas from late 1950s until 1975. Includes spring. Dimensions: Height - 4cm Diameter - 3.3cm For the seal between glass bowl and unit please see FL078.

Filter king fuel filter rubber seal. 

Filter king fuel filter & regulator with glass bowl

Inlet manifold gasket to fit all early carburettor 101 and 105 series cars. For later carburettor cars see code FL022 and for later Fuel Injected cars see FL039.

Inlet manifold gasket to fit all twin carburettor 105 series cars and Spica equipped models. Plus 116 and 75 models with carburettors (excluding V6 and TS). For early single carburettor cars see code FL022/1 and for later Fuel Injected cars see FL039...

Short vertical throttle rod (approx 97mm between centres) that fits between the carburettors on some Left Hand Drive 1750 and 2000 model 105 Series cars - and possibly some other versions too. Includes metal ends and spring retaining clips. Note that RHD...

Short vertical throttle rod (central aduster threaded rod is 45mm) that fits between the carburettors on twin carburettor 101 and 105 series cars. Includes metal ends and spring retaining clips. Note that this will fit right hand drive cars and some left...

Metal throttle rod end - use with new adjustable throttle rod - 2 required per rod. 

Ball joint, for the throttle linkage, works in conjunction with FL052/1.

Bush for the throttle linkage mechanism arm. Also used on the clutch pivot arm on mechanical clutches. 

Bush for the throttle linkage mechanism where it pivots on the firewall/bulkhead. Two required per car.