JUNIOR ZAGATO PARTS : BRAKES

Left side handbrake cable (looking from the rear of the car), to suit all ATE braked cars. This goes from main cable end on the centre of the differential to the handbrake mechanism in the wheel.

Handbrake housing rubber gasket. This is the gasket that sits at the base of the handbrake frame.

Handbrake shoe retaining pin holder to fit the handbrake mechanism on most 105 series cars from around 1968. Size 13.5mm narrowest diameter X 18mm widest diameter x 6.7mm height.

Short handbrake shoe spring to fit all 105 Series cars with ATE braking systems. One used per side, two per car. See BR093 for the matching long spring.

Long handbrake shoe spring to fit all 105 Series cars with ATE brakes. One used per side, two per car. See BR094 for the matching short spring.  

Handbrake lever assembly to fit the handbrake mechanism on ATE braked cars where the cable attaches to the handbrake mechanism.

Handbrake adjuster mechanism to fit the handbrake on all ATE braked system cars. Requires the 'sleeve' from your exisiting adjuster mechanism to work fully.

Rubber gaiter for the handbrake side cable where it connects to the backing plate of the rear brakes.

Handbrake shoe retaining spring for the pin that holds the shoes to the backing plate. One used per shoe, 4 used per car.

Handbrake shoe retaining pin to fit the handbrake mechanism on all ATE braked 105 Series cars. 1 used per brake shoe, 4 used per car.

Metal fork that screws to the front end of the handbrake cable where it attaches to the lever mechanism on all ATE braked 105 Series cars (and possibly Dunlop braked Sprint GTs & 1600 Roundtail Spiders as well).

Handbrake ratchet pawl end piece - bears against the rachet mechanism for the handbrake (available separately under code BR052).

Handbrake ratchet mechanism to fit all 105 Series cars. See also the pawl end piece that bears against the rachet under item code BR095.

Bonaldi servo sticker. Green & white, measuring 56mm X 19mm 

Brake / clutch pedal rubber with logo to suit all 105 Series cars. Although not original, the logo is a nice touch and reminiscent of the earlier Giulietta cars which did have this. Soften it in warm water before attempting to fit - you will find it much...

Brake and clutch pedal rubber to suit all 105 Series cars. Soften it in warm water before attempting to fit -you will find it much easier that way!

Brass male brake union - 3/8 UNF thread - to suit the braking system on all 105 series cars except for the caliper fittings. See item code BR321 for the union to fit into ATE brake calipers.  

Brass female brake union - 3/8 UNF thread - to suit the braking system on all 105 Series cars.

Brass brake union (male) M10 x 1 thread. This fits into the ATE calipers on all cars from 1968 onwards. Note that the remainder of the braking system uses 3/8 UNF threads.

Fantastic tool for straightening new brake lines to fit onto all Alfas - as well as other lesser marques. Allows you to create dead straight pipe runs for a factory finish look. For 3/16" pipe. Other versions available to order. To see how it works -...

Useful tool for bending new brake lines to fit onto all Alfas - as well as other lesser marques. Made specifically for use on 3/16" (4.76mm), steel, copper-nickel & copper pipes.

3/8 inch female to female brake line connector. Ideal for using to bypass the brake servo/booster units to test it's functionality.

Brembo DOT 4 brake and clutch hydraulic fluid. 0.5 (500ml) litre container.

Brembo DOT 4 brake and clutch hydraulic fluid. 1 litre container.