JUNIOR ZAGATO PARTS : FUEL

Misab carburettor washer set to suit cars with solid carb mounts. These gaskets will do 40mm/45mm/48mm carbs and are compatible with Webers, Dell'orto Solex.

Blanking plate for use where you are using a GTA oil cap and therefore do not need the standard breather elbow.

Gasket for the joint between the cam cover and breather elbow on 105 and some 116 models.

Mechanical fuel pump to fit all carburettor-equipped 105 series cars plus 101 series 1300 and 1600 Normale cars. Also fits some Alfetta models. Mounting gaskets and plastic spacer blocks are available separately. This is a new production...

Rubber style carburettor mounting kit (for a pair of carburettors) to suit cars that are using a solid alloy carb mount. This is a good alternative/upgrade to the regular thackery washers that are normally used.

Thackery washer, carburettor mounting. 5/16 - M8 fitting. 

Gasket for the fuel pump mounted on the lower front timing cover on carburettored 101 Normale and 105 Series cars plus 116 and 75 models with carbs.. There should be two gaskets fitted - one either side of the plastic insulating spacer block...

Aluminium blanking plate to seal off the mechanical fuel pump mounting on 101 and 105 series cars with cartridge oil filter. This is used when fitting an electric fuel pump to the car.

Aluminium blanking plate to seal off the mechanical fuel pump mounting on carb equipped 101, 105, 116 and 75 models. This is used when fitting an electric fuel pump to the car.    

Plastic mounting spacer to suit mechanical fuel pumps mounted down on the front timing cover of the engine. Fitted to most carburettor equipped 101, 105, 116 and 75 models.

M8 X 1.25 NUT. Used on solid carb mounts (FL081) to attach to the inlet manifold.

Set of 4 individual solid aluminium carburettor mounts to fit 40mm carburettors. Machined from solid aluminium and provided with gaskets on the carb side that have a built-in rubber seal to provide some absorption of engine vibration. Supplied with...

Viton fuel resistant rubber O ring to suit all solid carburettor mounts - as we have available under item codes FL017 and FL018. Ideal if you lose or damage an O-ring when fitting.

M8 x 1.0 nut. Fits the rubber carb mounts (FL014) used on most 105 series cars and the engine to bellhousing stud (EN135).

Siamesed carburettor rubber centre mount and two individual to suit 40mm carburettors. This mount replaces the two separate central mounts and bridges between the two carburettors. These must now be sold as a set as they may be slightly different...

Carburettor rubber mount to suit 40mm Weber, Dellorto and Solex carburettors. Used on all 105 series GT/GTV, Saloons and Spiders, early 116 4 cylinder as well as 101 Series Veloce cars. Normally 4 required per car. Paper gaskets for each side of...

Earth strap to fit the carburettor mounts on all 105 Series carburettor cars. Often missing or damaged on many cars we see, ideal to replace when you fit new carburettor mounts.

40mm paper carburettor mount gasket to fit 40mm Weber, Solex and Dellorto carburettor mounts. 2 required per rubber mount/carburettor throat. Hole spacing - 72mm ** NOTE ** - Some 1600 S3/S4 Spiders (and some late Alfettas) use a gasket with 80mm...

Gasket to fit between the air intake trough/plenum and the carburettor body on all carburettored 105, 116 and 75 engines (not TS or V6).

Rubber gasket filter for aluminium trough to tubular air filter canister ('68-'78)

Full carburettor rebuild kit to suit Weber 40 DCOEs - kit does 2 carburettors

Carburettor rebuild kit to suit Weber 45 DCOEs - kit does 2 carburettors

Rebuild kit to suit Solex DDH carburettors. One kit does 2 carburettors.

Carburettor rebuild kit to suit Dell'orto dhla40 carburettors - kit does 2 carburettors.