105 COUPE PARTS : OTHER RUBBER PARTS

Here is a diagram showing the location of some of the parts in this category.

Here is a diagram showing the location of some of the parts in this category.

Here is a diagram showing the location of some of the parts in this category.

Headlight seal to fit all 105 Series Spiders 1966 - 93 without perspex headlight covers - such as Spider Junior and all USA models. Cars fitted with covers do not use a seal. Also fits early GT (1964-67), early Giulia saloon, 2600 Sprint, 2000/2600...

Pair of headlight wiring grommets to fit into the rear of the headlight bowl on all 105 Series Spiders 1966-93 and all Step-front GTs. Can also be used in the outer headlight bowls on some 1750 2000 GTVs, GT Juniors and all Saloons. Suitable for...

A pair of outer headlight seals  - fit between the outer rim and the headlight lens to waterproof the headlight bowls. Fits (according to parts books) all Carello headlamp cars as follows:750 Series Sprints from chassis number 1493.05801 onwards, Sprint...

Grommet to fit into the lubricant filler hole on the top of Burman steering boxes on 105 Series cars.

Rear windscreen seal for all 105 series GT, GTV and GTA cars.

Front windscreen/windshield rubber seal for all 105 series GT, GTV, GTC and GTA cars.

Joining piece to fit screen surround GT and GTV models, will fit front and rear screens.

GT rear screen insert - nicely made anodised aluminium extruded section that fits into the screen rubber. Please note that supply oF this part can be very erratic as they are only produced in small numbers on an irregular basis. We cannot guarantee...

GT front screen insert - nicely made anodised aluminium extruded section that fits into the screen rubber. Please note that supply of this part can be very erratic as they are only produced in small numbers on an irregular basis. We cannot guarantee...

Pair of rubber seals for the sidelights to body on all step-front GTs. See item code LT090/1 for the internal sidelight lens to sidelight body seals.

Pair (left and right) of front sidelight to bumper seals to fit Mk 1 1750 GTVs and Berlinas.

Pair of rubber electric cable boots to fit inside the front wing/fender where the wires connect to the 'long' style side repeaters fitted to Step-front GTs and GTAs and Giulia Saloons.

Rubber strip for the bumper over-riders on 1750 GTV Mk 2, 2000 GTV and some saloons. Goes between the over-rider and the main bumper. Sold per length to suit one over-rider, 4 required per car.

Over-rider rubber to fit 1750 GTV Mk 2, 2000 GTV and some saloon models. 4 required per car.

Large rubber seal/gasket that fits between the transmission tunnel pressing and the transmission tunnel apeture cover (either metal or plastic/foam versions) on most of the 105 series range. Fitted to Sprint GT, GTV, GTC GTA models, all Roundtail...

Large rubber floor bung to fit into the pressing holes in the floor panel of all 105 Series cars. Also used in the spare wheel well too. Total 8 required for GTs, Saloons and Montreals and 6 required for Spiders. Also fits many 116 and 75 models...

Rubber gaiter that fits over the transmission tunnel aperture cover (that attaches to the transmission tunnel pressing) inside the cockpit of all 105 series Coupes, Saloons and Spiders. Is covered by the centre console in cars with the consoles fitted...

Rubber seal for heater box. Fits all 105 series cars from 1968 onwards.

Rubber seal for the leading edge of a Step-front bonnet (hood). Glues to the underside of the leading edge of the bonnet/hood and seals against the top of the front bodywork. 

Rubber seal that sits along the front edge/lip of the scuttle grille panel on all 105 Series GTs/GTVs.

Set of three rubber stoppers for the pedal box on left-hand drive standing pedal 105 series cars 1964-69.