105 SALOON PARTS : OTHER RUBBER PARTS

Headlight seal to fit all 105 Series Spiders 1966 - 93 without perspex headlight covers - such as Spider Junior and all USA models. Cars fitted with covers do not use a seal. Also fits early GT (1964-67), early Giulia saloon, 2600 Sprint, 2000/2600...

Pair of headlight wiring grommets to fit into the rear of the headlight bowl on all 105 Series Spiders 1966-93 and all Step-front GTs. Can also be used in the outer headlight bowls on some 1750 2000 GTVs, GT Juniors and all Saloons. Suitable for...

Grommet to fit into the lubricant filler hole on the top of Burman steering boxes on 105 Series cars.

Front windscreen seal to suit Giulia/Berlina saloons.

Rear screen rubber to suit all versions of the Giulia saloon.

Rear screen rubber to suit 1750 and 2000 Berlina saloons.

Pair (left and right) of front sidelight to bumper seals to fit Mk 1 1750 GTVs and Berlinas.

Pair of rubber electric cable boots to fit inside the front wing/fender where the wires connect to the 'long' style side repeaters fitted to Step-front GTs and GTAs and Giulia Saloons.

Rubber seal/flap that fits across the rear of the engine bay on the early Giulia saloons.

Rubber seal/flap that fits across the rear of the engine bay on Giulia saloons.

Rubber strip for the bumper over-riders on 1750 GTV Mk 2, 2000 GTV and some saloons. Goes between the over-rider and the main bumper. Sold per length to suit one over-rider, 4 required per car.

Over-rider rubber to fit 1750 GTV Mk 2, 2000 GTV and some saloon models. 4 required per car.

Large rubber seal/gasket that fits between the transmission tunnel pressing and the transmission tunnel apeture cover (either metal or plastic/foam versions) on most of the 105 series range. Fitted to Sprint GT, GTV, GTC GTA models, all Roundtail...

Large rubber floor bung to fit into the pressing holes in the floor panel of all 105 Series cars. Also used in the spare wheel well too. Total 8 required for GTs, Saloons and Montreals and 6 required for Spiders. Also fits many 116 and 75 models...

Rubber gaiter that fits over the transmission tunnel aperture cover (that attaches to the transmission tunnel pressing) inside the cockpit of all 105 series Coupes, Saloons and Spiders. Is covered by the centre console in cars with the consoles fitted...

Rubber seal for heater box. Fits all 105 series cars from 1968 onwards.

Metal pedal cover plate to fit all left hand drive Giulia models with standing pedals.

Set of three rubber stoppers for the pedal box on left-hand drive standing pedal 105 series cars 1964-69.

Rubber seal to fit between the pedal housing and the bodywork on all left hand drive 105/115 Series cars with hanging pedals.

Get the rubber pedal base seal & the metal retaining bracket (to suit all right hand drive 105 series cars with floor hinged pedals) RB066 and RB067 together for a better price!

Metal pedal base seal bracket to retain the rubber seal available under code RB066 on all right hand drive 105 Series cars.  Note that this bracket will require some 'relieving' on the inner left side to fit properly to the car. It's much better that the...

Right hand drive pedal base seal - for all rhd cars from 1964 to 1978. To properly fit the boot, the pedal box must be removed from the car and the pedal shafts removed from the pivot. The boot is fitted by inserting the shaft of the pedal through from...

Pair of rear numberplate light seals to suit 101 Series Spiders. Light units available separately under code 750-311 or 750-311/1 (non Carello version). Can also be used on the same light units fitted to all 105 Series GT/GTVs up to the 1750 Mk 1, early...

Pair of rubber seals to fit on the front edge of the rear door on all Giulia saloons.