105 SPIDER PARTS : OTHER FUEL SYSTEM PARTS

Short rubber air intake hose that connects between the cross-over air hose (FL035) and the intake plenum on all Bosch injected Spiders 1988-93. 1 per car, approximately 70mm internal diameter. If you require the hose clip for this part, please see part...

Cross-over induction air hose for Bosch injected Spiders 1982-93. It goes from the air flow meter housing across the engine to the plenum chamber. If you require the hose clip for this part, please see part FL094

Short air intake tubes than fit between the plenum chamber and inlet manifold on late model Bosch injected Spiders and all Spica equipped GTs and Spiders. 4 per car - approx 45mm internal diameter.

Air filter housing fitted to all early 105 cars with crossover air hose. 

M8 x 1.0 nut. Fits the rubber carb mounts (FL014) used on most 105 series cars and the engine to bellhousing stud (EN135).

Inlet carburettor gasket found on Series 4 1600 Spiders and also some late S3 Spiders and Alfettas. Four required per car. 80mm hole spacing. You will also need four FL021. If you require the carburettor supports please see FL096 & FL097 Inlet...

Inlet manifold gasket found on Series 4 1600 Spiders and also some late S3 Spiders. If you require the carburettor supports please see FL096 & FL097 Paper gaskets are available under code FL021 and also code FL098.       

40mm Carburettor twin rubber centre mount used on Series 4, 1600 Spiders and found on some late S3 Spiders. If you require the outer single support please see FL096 S4 1.6 CARBURETTOR RUBBER MOUNT - 40mm ALSO LATE 116 & 75 Paper gaskets are...

40mm Carburettor rubber mount used on Series 4 1600 Spiders and found on some late S3 Spiders. If you require the centre double support please see FL097 S4 1.6 CENTRE CARBURETTOR RUBBER MOUNT - 40mm Paper gaskets are available under code FL021...

Carburettor rubber mount to suit 45mm carburettors. Sold individually, 4 required per car.

Siamesed carburettor rubber centre mount and two individual to suit 40mm carburettors. This mount replaces the two separate central mounts and bridges between the two carburettors. These must now be sold as a set as they may be slightly different...

Carburettor rubber mount to suit 40mm Weber, Dellorto and Solex carburettors. Used on all 105 series GT/GTV, Saloons and Spiders, early 116 4 cylinder as well as 101 Series Veloce cars. Normally 4 required per car. Paper gaskets for each side of...

Earth strap to fit the carburettor mounts on all 105 Series carburettor cars. Often missing or damaged on many cars we see, ideal to replace when you fit new carburettor mounts.

45mm paper carburettor gasket. ** NOTE ** - Unmodified cars will use the 40mm gasket instead (FL021).

40mm paper carburettor mount gasket to fit 40mm Weber, Solex and Dellorto carburettor mounts. 2 required per rubber mount/carburettor throat. Hole spacing - 72mm ** NOTE ** - Some 1600 S3/S4 Spiders (and some late Alfettas) use a gasket with 80mm...

Solid aluminium 45mm carburettor mount set - 62 mm length to fit 45mm carburettors in black anodised finish.  Machined from solid aluminium then fitted with an O-ring on one face to provide both a seal and some absorption of engine vibration. Supplied...

Set of 4 individual solid alloy carburettor mounts to fit 45mm carburettors. Set includes 'O' rings , thackery washers and nylock nuts for the carb side plus plain nuts for the inlet manifold side. PLEASE NOTE, THE 'O' RING IS FITTED AGAINST THE...

Gasket to fit the crossover style aluminium air filter housing fitted to all twin carburettor 105 Series cars 1300 to 1750 up to 1969. Fits between the lid and the body of the housing that bolts to the carburettors.

Gasket to fit between the air intake trough/plenum and the carburettor body on all carburettored 105, 116 and 75 engines (not TS or V6).

Rubber gasket filter for aluminium trough to tubular air filter canister ('68-'78)

Full carburettor rebuild kit to suit Weber 40 DCOEs - kit does 2 carburettors

Carburettor rebuild kit to suit Weber 45 DCOEs - kit does 2 carburettors

Rebuild kit to suit Solex DDH carburettors. One kit does 2 carburettors.

Carburettor rebuild kit to suit Dell'orto dhla40 carburettors - kit does 2 carburettors.